Results 1 to 5 of 5
  1. #1

    holeshot bogging

    I have a 2001 GP1200R with a few minor engine mods, flame arrestors, D-Plate and cat clip, wave-eater clips and a holeshot kit. I also have sealed the pump and changed out the impeller. At the end of last season the oil line on number 3 failed and seized. I rebuilt the top end during the winter, switched to pre-mix and sent the Carbs to Carl at island racing.

    After 10 hours of so of careful break in I have begun to turn the ski loose. I change out the plugs(BR8ES-11) and gone to 40:1 mix with AMS interceptor and running shell premium gas.

    The issue is the hole shot, the ski bogs down and the engine sputters from around 2K rpm till about 4K rpms, at which point it will either stall like itís getting to much fuel or finally take of and run great. Thos only occurs if you hit the throttle hard from a slow pace, if you slowly feather the throttle it does not happen as often. It seems to occur when the ski is just started after resting as well as after riding the hell out of it. The ski runs great in all other aspects good top end not issues at all other than the hole shot from a stand still or a 1-2 mph idle. I can find no exhaust leaks or issues with gaskets etc. I donít know much about tuning carbs thatís why I left it to Carl. Is it getting to much fuel from the low speed idle?

  2. #2
    I recently had my carbs rebuilt by Carl and know it's running rich on the low end. It smokes pretty good while idling and I can smell the gas out the exhaust. Did you get t-handles installed? You may want to check where they're set. I do have a slight bog from idle to WOT, but nothing as bad as yours. Maybe this will help.

  3. #3
    dewzee1200's Avatar
    Join Date
    Aug 2010
    Location
    Lake Martin Alabama
    Posts
    103
    +1
    1
    No One has any suggestions?

  4. #4
    Hurricane1000's Avatar
    Join Date
    Oct 2005
    Location
    Gulf of Mexico
    Posts
    1,008
    +1
    106
    Quote Originally Posted by dewzee1200 View Post
    No One has any suggestions?
    Try to adjust your low speed needle setting "In" 1/8 a turn...this will help lean your low end and maybe clear it up......
    Easy test.


  5. #5
    Tool Bag water worx's Avatar
    Join Date
    Aug 2006
    Location
    Sunny Fla
    Posts
    2,359
    +1
    132
    Quote Originally Posted by dewzee1200 View Post
    No One has any suggestions?
    I guess after 10 years someone would answer... LOL

    If you are looking for a answer you should start a current thread,stating your problem.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2013 rxpx bogs and no holeshot
    By Born2Ride in forum 4-Tec Performance
    Replies: 3
    Last Post: 07-06-2016, 09:47 AM
  2. Holeshot bog and plug colors...
    By xray328 in forum Yamaha PWC Performance (2-stroke)
    Replies: 16
    Last Post: 09-05-2012, 09:58 AM
  3. Bogging in the Holeshot
    By njgprider in forum Yamaha PWC Performance (2-stroke)
    Replies: 24
    Last Post: 08-30-2009, 10:21 PM
  4. Nice Holeshot of an older HX racing ...
    By VFX_Artist in forum Videos & Pictures
    Replies: 2
    Last Post: 12-09-2005, 04:24 AM
  5. Motor bogs down when jumping...
    By Denali44 in forum 4-Tec Performance
    Replies: 8
    Last Post: 08-08-2005, 03:53 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •