Results 1 to 7 of 7
  1. 06-02-2008, 11:37 AM #1
    SantaCruz163
    SantaCruz163 is offline
    SantaCruz163's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    316

    Thread size for water rail bolts

    Does anyone know what the thread size is for the water rail bolts on the cylinder heads?
    Reply With Quote Reply With Quote

  2. 06-02-2008, 02:09 PM #2
    Keddano
    Keddano is offline
    SPEED KILLS, BUT YOU GET THERE QUICKER Keddano's Avatar
    Join Date
    Jul 2007
    Location
    Cedar Rapids,Iowa
    Posts
    6,380
    +1
    23
    I just put a rail on yesterday,Pretty sure it's a 6mm thread,Do you need a length?
    Reply With Quote Reply With Quote
  3. 06-02-2008, 05:35 PM #3
    SantaCruz163
    SantaCruz163 is offline
    SantaCruz163's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    316
    Nope, just the size. I need to helicoil one of the holes.
    Reply With Quote Reply With Quote
  4. 06-02-2008, 05:51 PM #4
    Keddano
    Keddano is offline
    SPEED KILLS, BUT YOU GET THERE QUICKER Keddano's Avatar
    Join Date
    Jul 2007
    Location
    Cedar Rapids,Iowa
    Posts
    6,380
    +1
    23
    I can double check in about a hour if you want.
    Reply With Quote Reply With Quote
  5. 06-02-2008, 08:54 PM #5
    SantaCruz163
    SantaCruz163 is offline
    SantaCruz163's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    316
    Yea, double check just to be sure. Thanks.
    Reply With Quote Reply With Quote
  6. 06-02-2008, 08:59 PM #6
    beerdart
    beerdart is offline
    Moderator beerdart's Avatar
    Join Date
    Aug 2006
    Location
    CT
    Posts
    25,961
    +1
    1,442
    m6 is correct.
    Reply With Quote Reply With Quote
  7. 06-02-2008, 09:47 PM #7
    Keddano
    Keddano is offline
    SPEED KILLS, BUT YOU GET THERE QUICKER Keddano's Avatar
    Join Date
    Jul 2007
    Location
    Cedar Rapids,Iowa
    Posts
    6,380
    +1
    23
    Yep
    Reply With Quote Reply With Quote
« Looking for opinions on a 1200. Pro or slx? | Exhaust Pipe/Exhaust Manifold Gasket Install »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Rivet size for rub rail..
    By turboman412 in forum Kawasaki PWC Performance (2-stroke)
    Replies: 1
    Last Post: 05-06-2015, 02:38 PM
  2. Intercooler block off - Thread size for barb fitting
    By Badvgood in forum 4-Tec Performance
    Replies: 3
    Last Post: 04-08-2013, 07:59 AM
  3. Domestic engine - What is the thread size for the main crank case studs?
    By K447 in forum Polaris Open Discussion
    Replies: 6
    Last Post: 06-20-2012, 05:54 AM
  4. thread size for drive shaft..
    By henn in forum Conversion FAQ and Tips
    Replies: 12
    Last Post: 05-27-2010, 04:04 PM
  5. What is the tap or thread size for Prop?
    By tomgtv in forum Kawasaki PWC Performance (4-stroke)
    Replies: 1
    Last Post: 08-04-2009, 04:02 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules