Results 1 to 10 of 11
Thread: OPAS question
-
06-06-2006, 03:24 PM #1
- Join Date
- Apr 2006
- Location
- South Ogden, Utah
- Posts
- 92
OPAS question
I have an 05 RXT...I just want to keep my OPAS in the tucked up position...how do I do that? When im flying down the river at WOT I see my OPAS are dragging. But ive checked my screens and no clogs anywhere...
-
06-06-2006, 04:23 PM #2
slot some PVC pipe ...I think it's 1/2"
-
06-07-2006, 04:51 AM #3
- Join Date
- Aug 2005
- Location
- Jerry's guest bedroom
- Posts
- 3,469
- +1
- 2
3/4" x 2" with a 1/4" slot.
-
06-07-2006, 09:48 AM #4
- Join Date
- Apr 2006
- Location
- South Ogden, Utah
- Posts
- 92
so the inside diameter needs to be 1/4 inch, the piece needs to be 2 inches long, and the 3/4 stands for the outside diameter? Am i even close?
-
06-07-2006, 10:09 AM #5
3/4 inch PVC cut at 2 inches long. Cut a 1/4 inch groove out of the length so it will be able to "snap" over your OPAS rod.
Hope that helps.
-
06-07-2006, 10:23 AM #6
if u confused... then post saying u dont have a clue and i'll take a picture and post for u..
but these guys got u on the right track so far.
-
06-07-2006, 04:25 PM #7
except it's 1/2" PVC that you use. has 1/2" ID and 3/4" OD, cut a slot , I used a 4" grinder, took like a minute to slot both pieces
-
06-07-2006, 04:29 PM #8
i guess it'll all work. I used 3/4" PVC when i did it on two skis. 1/2" might be more exact, but good luck ever getting them off without cracking them off or grinding them off. it was hard enough to get the 3/4" pieces off when it came time for OPAS block offs
-
06-07-2006, 07:30 PM #9
If you have a problem spreading open the tubing, then just warm it up a little either in very Hot water for a few minutes or use a heat gun on low...PR...
-
06-07-2006, 07:51 PM #10
very easy to get the 1/2" off, just disassemble and pull the shaft out of the PVC.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Rxp255 opas question
By james747 in forum 4-Tec PerformanceReplies: 3Last Post: 01-13-2015, 10:19 PM -
Performance opas questions
By rxp12 in forum 4-Tec PerformanceReplies: 22Last Post: 12-15-2009, 05:54 PM -
Performance opas questions
By rxp12 in forum Sea Doo Open DiscussionReplies: 3Last Post: 12-11-2009, 10:49 PM -
OPAS Question
By Yellow04RXP in forum 4-Tec PerformanceReplies: 5Last Post: 05-25-2007, 07:06 PM -
OPAS questions
By RaggedJoe in forum Sea Doo Open DiscussionReplies: 11Last Post: 11-15-2005, 08:15 PM
So I found a Bosch 0280750009and threw it on the ski. I needed 4 6mmx45mm...
2018 RXTX300 Cutting out under...