Results 1 to 10 of 46
-
06-19-2005, 12:13 PM #1
- Join Date
- May 2005
- Posts
- 607
- +1
- 2
Boost gauge, Gps, Depth Gauge ideas
Here are pics of what I did. Nice clean look.
-
06-19-2005, 12:29 PM #2
Sweet! I thought about putting my boost gauge there, but could not find a pod to make it fit properly.
-
06-19-2005, 12:53 PM #3
-
06-19-2005, 12:59 PM #4
- Join Date
- May 2005
- Posts
- 607
- +1
- 2
Hulk, that is an autometer gauge and autometer trim ring. The ring is taller on one side, so you can spin it to get the angle you want. The rings come three in a pak for around $12. You need to cut a 2 23/32" hole and can use the stock mounting bracket that comes with the gauge, which will need to be cut on both stubs with one stub being longer than the other. I marked the center and covered the area with duct tape then used a 2 5/8" hole saw and trimmed with a utility knife and file to get the perfect fit. Are those grips and seat cover sweet or what? Getting rid of the red seat makes the boat look a lot richer.
-
06-19-2005, 01:05 PM #5
- Join Date
- May 2005
- Posts
- 607
- +1
- 2
sprcharded, the depth gauge is a Hawkeye DF1120S. I mounted the transducer below the engine in the front left area. Not picking up the depth very good currently. I need to try another spot. If that doen't work I may need to go trnnsom mount. Wanted to avoid drilling a hole in the hull if possible. If your'e interested I can post pics of the wiring and module mounting location.
-
06-19-2005, 02:18 PM #6
Nice! Does anyone make a combo Fuel/Oil/Boost pressure gauge cluster? That would be nice to have on these skis.
-
06-20-2005, 12:43 PM #7
can some one please explian why some one would want and use a boost gauge for?
-
06-20-2005, 12:54 PM #8
The boost gauge will help you diagnose a slipping clutch before it goes thus avoiding disintegrated ceramic washers.
-
06-20-2005, 01:12 PM #9
got any pics where you tapped boost gauge into the intake manafold?
-
06-20-2005, 01:26 PM #10
looks awesome..very creative. just out of curiousity..is the gauge sealed..meaning waterproof?
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
J-Pipe Boost gauge Idea - With Pics
By LugNutLS1 in forum Yamaha PWC Performance (4-stroke)Replies: 13Last Post: 09-12-2014, 08:54 AM -
Dynotune boost gauge mounting ideas
By Extrememotors in forum 4-Tec PerformanceReplies: 4Last Post: 05-13-2008, 05:34 AM -
Pics of the Boost Gauge
By Red Devil in forum 4-Tec PerformanceReplies: 15Last Post: 02-27-2006, 09:43 AM -
Boost Gauge, again.......
By Kinchyle in forum 4-Tec PerformanceReplies: 59Last Post: 09-30-2005, 10:09 PM -
Boost Gauge
By Red Devil in forum 4-Tec PerformanceReplies: 3Last Post: 08-09-2005, 09:09 AM
https://drive.google.com/file/d/1upWKJ_QxAZOXSZis6xNb3sEIupjF8s_D/view?pli=...
2015 Kawasaki 310LX Charging issue