Results 1 to 10 of 10
  1. 05-25-2006, 10:23 AM #1
    jasonj2004
    jasonj2004 is offline
    Join Date
    Apr 2006
    Location
    Roanoke, Al.
    Posts
    9

    nose cone walked up shaft

    my green solas nose cone walked up the drive shaft and I can't seem to get it to move in any direction should I take it to a dealer or try to get it off myself and how would i go about doing it? thanks
    Reply With Quote Reply With Quote

  2. 05-25-2006, 10:48 AM #2
    Red Devil
    Red Devil is offline
    Red Devil's Avatar
    Join Date
    Apr 2005
    Location
    Chesterfield/Richmond, VA
    Posts
    1,809
    Just try harder, don't waste your time and money taking it to a dealer. Get something up in there long enough and just keep tapping until it comes off. It is probably just stuck in that one area and needs a good "whack!"
    Reply With Quote Reply With Quote
  3. 05-25-2006, 12:09 PM #3
    bling bling
    bling bling is offline
    Nobody Really bling bling's Avatar
    Join Date
    Apr 2005
    Location
    Lake Lanier Georgia
    Posts
    374
    +1
    1

    Re: nose cone walked up shaft

    Quote Originally Posted by jasonj2004
    my green solas nose cone walked up the drive shaft and I can't seem to get it to move in any direction should I take it to a dealer or try to get it off myself and how would i go about doing it? thanks
    when you did get it back off shaft make sure to use some red locktite and or a set screw. These thing are very hard to keep in place . I ended up puting my stock on the solas never had the problem again and didnt loose any performance
    Reply With Quote Reply With Quote
  4. 05-25-2006, 01:42 PM #4
    jasonj2004
    jasonj2004 is offline
    Join Date
    Apr 2006
    Location
    Roanoke, Al.
    Posts
    9
    ok I will try hitting it harded but it seems like the o-rings inside are bilding on the shaft
    Reply With Quote Reply With Quote
  5. 05-25-2006, 01:44 PM #5
    RX951
    RX951 is offline
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,074
    +1
    25
    make sure to use some red locktite and or a set screw.
    Reply With Quote Reply With Quote
  6. 05-25-2006, 02:29 PM #6
    Water4fire
    Water4fire is online now
    Water4fire's Avatar
    Join Date
    May 2005
    Location
    New Braunfels TX.
    Posts
    10,380
    +1
    873
    Spray some lube up in it to allow the O-ring to slide...

    ...
    Reply With Quote Reply With Quote
  7. 05-25-2006, 02:47 PM #7
    Jeff C
    Jeff C is offline
    Resident Jicky Jack Jeff C's Avatar
    Join Date
    May 2005
    Location
    Twin Cities, MN
    Posts
    1,153
    +1
    2
    When you do get it off, mess up the threads a bit so it will harder for it to come off next time.

    I took a wood chisel and hit the threads sideways in two places, and screwed it on there with some clear silicone, and I will have to wreck it to get it off.....

    It has not moved at all since I did that early last year
    Reply With Quote Reply With Quote
  8. 05-25-2006, 02:49 PM #8
    1 FAST VE
    1 FAST VE is offline
    David 1 FAST VE's Avatar
    Join Date
    Jun 2005
    Location
    Southaven, MS
    Posts
    1,958
    +1
    1
    Do as Austin suggested and if possible take a pair of channel locks and put on the drive shaft. Don't hold tight just enough to hold in front of the cone.

    Then hit the channel Locks this way you are hitting all the way around the cone not just in one place.

    Good Luck!
    Reply With Quote Reply With Quote
  9. 05-25-2006, 03:07 PM #9
    jasonj2004
    jasonj2004 is offline
    Join Date
    Apr 2006
    Location
    Roanoke, Al.
    Posts
    9
    Doing this will not pull the drive shaft out of the motor or damage the carbon seal will it
    Reply With Quote Reply With Quote
  10. 05-25-2006, 03:35 PM #10
    bling bling
    bling bling is offline
    Nobody Really bling bling's Avatar
    Join Date
    Apr 2005
    Location
    Lake Lanier Georgia
    Posts
    374
    +1
    1
    Quote Originally Posted by jasonj2004
    Doing this will not pull the drive shaft out of the motor or damage the carbon seal will it
    no it will not you will find it just in a bind kinda sideways . i had this issue with mine and i am sure other did till they figure trick to keep cone on
    Reply With Quote Reply With Quote
« RXT vs RXP ECU | Anybody mess with this? »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Nose cone stuck on shaft
    By excess in forum 4-Tec Performance
    Replies: 9
    Last Post: 09-02-2006, 12:14 PM
  2. impeller nose cone keeps moving forward on shaft
    By jgustman in forum Yamaha PWC Performance (2-stroke)
    Replies: 7
    Last Post: 07-26-2006, 07:02 PM
  3. How do you keep nose cone on?
    By Pale Rider in forum 4-Tec Performance
    Replies: 16
    Last Post: 02-14-2006, 04:37 PM
  4. 3 km/h nose cone???
    By BDNJ in forum 4-Tec Performance
    Replies: 5
    Last Post: 01-06-2006, 10:21 AM
  5. Nose cone coming off.
    By Mark S in forum 4-Tec Performance
    Replies: 7
    Last Post: 08-20-2005, 03:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules