Results 1 to 10 of 14
Thread: Reflashed ECU is SICK!!!
-
03-19-2006, 11:12 PM #1
Reflashed ECU is SICK!!!
I Got my parts from Mark U fri.
All I can do is Smile at the way this thing pulls right up to the danger zone
First I installed my RR thru hull (love the sound of that pipe), and tested to check for any leaks, then I Installed my reflashed ECU. With my 14/19 solas, and 84mm honed stock nozzle,I slowly ran it up to 8400-8450 , and was only at half throttle
. So I went back to the dock, and put on my 81.5mm nozzle to keep the Rpms down to a safe level. Man the acceleration is awesome, it is now running at 8200-8300, until I install the RR retainers,RRcam gear, and RR valve spring shims this week. Then I can pitch the prop, and play with the nozzles some more to see how fast I can get it up to.
-
03-19-2006, 11:21 PM #2
glad to hear! i'm also glad to hear you are diciplined enough to install the retainers and washers before you let her rip.
-
03-19-2006, 11:31 PM #3
Oh yeah, Too much$$$$ into this to drop a valve or worse
Thanks again Mark, Now I just need 2 get it dialed in for the FRS in 2 weeks. I'm still gonna get the 3 blade, and the "B" kit charger to add to all of this
Gonna be a fun summer 4 sure.
-
03-20-2006, 12:31 AM #4
My wife won't let me wash the Sea doo parts in the kitchen sink.
-
03-20-2006, 01:16 AM #5
-
03-20-2006, 07:52 AM #6
Originally Posted by gtxsc03
-
03-20-2006, 06:52 PM #7
Psycho, in another thread you mentioned you have replaced motor mounts twice - was that the front motor mount both times? Have you replaced it with the better one now available?
-
03-20-2006, 07:31 PM #8
Vern I replaced only 1 of the rear ones. First the left one, then found out on the right rear the allen bolts came loose from the hull 6 mos. later.
no front one yet. If that one goes I will buy the rotax one to replace it with.
-
03-20-2006, 07:38 PM #9
psycho: Dude that is SWEET!!!
I see you have your BOV hooked up, any probs with your clutch using that? I just heard it was best to leave it dis-connected...
Awsome, and I see you have the O2 sensor in the J-pipe, nice work bro!...PR...
-
03-20-2006, 07:54 PM #10
Thanks PR, I had my local weld shop buddies do it for me, It came out great, and they didn't even charge me for it
I cut the hole, and prepped it for them tho :P The BOV came with the New riva kit, but I had my last one blocked off,and removed.I plan on doing the same to this one, just hooked it up for the weekend test
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
5 good reason WHY a aftermarket ECU is better the reflash. No Mods to delete or close
By RichieFZR in forum Yamaha PWC Performance (4-stroke)Replies: 17Last Post: 05-17-2011, 08:56 PM -
2009 RXT iS 255 Les cooke reflash ECU
By Ken IS255 in forum 4-Tec PerformanceReplies: 3Last Post: 04-22-2011, 11:36 PM -
Reflash ecu
By rancarts in forum 4-Tec PerformanceReplies: 21Last Post: 03-04-2006, 02:49 PM -
The reflashed ECU's are on the way back!
By Green Hulk in forum 4-Tec PerformanceReplies: 19Last Post: 02-14-2006, 04:23 PM -
reflash ecu
By rancarts in forum 4-Tec PerformanceReplies: 41Last Post: 02-06-2006, 10:12 PM
rxp 2019 14hrs, with supertech valves, supertech springs, supertech...
SuperTech Lightweight Valves /...