Results 1 to 10 of 28
Thread: gained 40 RPMs removing washer
-
08-09-2007, 10:02 AM #1
gained 40 RPMs removing washer
I took the washer out from behind the prop, and Gained 40 RPMs.
This was done with back to back testing.
Just figured I would let everyone know.
prop was a DF 14/24.5 SB
-
08-09-2007, 10:23 AM #2
I have some issues with the upgraded washers. I have had one actually come over the lip of the dynafly and get stuck on the OD of it. From my comparison of the new washer to the old it seems the old washer actualy spaced the impeller from the lip on the pumpshaft the new ones do not. I also see that depending on how accurate the shaft is pressed in and located (shoulder of shaft to pump housing) makes a difference. The only function I see for the new washer is to give some initial protection to the pump seal I see no other benefit. Glad to see you found some more RPM's
-
08-09-2007, 11:24 AM #3
- Join Date
- Apr 2007
- Location
- NASHVILLE
- Posts
- 438
have you removed the cone in front of the prop?
-
08-09-2007, 01:06 PM #4
-
08-09-2007, 02:53 PM #5
thats odd....removal of the spacer will load the pump more.
-
08-09-2007, 03:03 PM #6
Ok, not looking to start anything - I really want some info on your testing. Did you test before/after with the engine warm? I'm just wondering if the extra rpm's are from your engine having cooled down while removing the washer. We're all looking to eek out some extra rpm, so if this really works, I may try it.
Thanks-
Boogie
-
08-09-2007, 03:22 PM #7
no prob man. not only did I do back to back testing within 5-10 minutes, I also tested the prior day
all I could get on day one and 2 was 7030. on day 2, 5-10 minutes after SEVERAL runs, buy me and another person, I took the washer out and gained 40 RPMs. put the washer back in lost 40 RPMs, took it back out gained, and left it out.
figured I would try to post something good in the midst of all the bad going around right now
-
08-09-2007, 03:45 PM #8
I would think you would be turning that prop more than that with a big bore?
You are talking about removing the donut/spacer that keeps the prop out of the pump?
-
08-09-2007, 04:03 PM #9
yes, that washer, it is a big thick washer.
this prop was done by carl, and it is WAY too steep
-
08-09-2007, 04:26 PM #10
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Full retard vs full advance gained 300+ rpms and almost 4 mph
By Vern in forum 4-Tec PerformanceReplies: 225Last Post: 12-17-2013, 02:14 AM -
Gained 120+ RPM's!
By NOONZ in forum 4-Tec PerformanceReplies: 10Last Post: 10-24-2011, 08:00 PM -
I gained 250 rpms!
By Vern in forum 4-Tec PerformanceReplies: 50Last Post: 05-15-2008, 07:09 AM -
speed & rpm after washers
By bigjohnson in forum Sea Doo Open DiscussionReplies: 11Last Post: 07-22-2007, 02:29 PM -
i gained 450+ rpms from 81mm to 82mm
By Shibby1485 in forum 4-Tec PerformanceReplies: 25Last Post: 04-27-2006, 09:00 PM
Thanks for the correction regarding the cam, I think the timing was...
GP1300R built for Harley Davidson...