Results 1 to 10 of 10
-
07-28-2007, 02:59 AM #1
MSX 140 overhetting after 10 min.
[FONT='Calibri','sans-serif']Hi! Today, I was raced with my MSX 140, after 10 min. I see that red led is blinking and in to the display warning critical temperature check eng.after checking I see that no water circulation, inlet pipe is clean, ,but when I’m open flash pipe, were water high temperature ,after ,that water wait out ,led over blinking, and my msx is went perfectly but only 10 minuets ,after thigh all once more, where is problem, what is the water circulation problem?[/FONT]
-
07-28-2007, 07:31 AM #2
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,375
- +1
- 102
Welcome to the Hulk. Have you checked your thermostat for proper operation? #10 in the pic. http://partsland.com/index.cgi?N=118...COOLING-SYSTEM
-
07-28-2007, 07:59 AM #3
I'M taked him out ,and the same problem, i'm think, that thome ruber water line is closed ,must check what is...
-
07-28-2007, 08:03 AM #4
when i connect flash kit in to the heads place, and start motor, hi is not overhetted, and temperature about 55-65
,SO I,M THINK SOMETHING happend with inlet line...Can i drivewithout termostat? In Israel water about 30
-
07-28-2007, 08:16 AM #5
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,375
- +1
- 102
If you mean 30* Celsius ,I'm sure you could. If you mean 30* Farenheit you'll need the thermostat for sure.
-
07-28-2007, 08:27 AM #6
-
07-28-2007, 08:29 AM #7
all it happend after replace engine, were raded 9 ours, and happend.
-
07-28-2007, 08:37 AM #8
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,375
- +1
- 102
As long as it and all hoses are clear, you should be fine. Is your ski equipped with a rubber exhaust hose? If it is, check to see if it's soft or squishee feeling. It's possible it's collapsing under a load and causing the overheat.
-
07-28-2007, 08:42 AM #9
rubber exhaust hose only in connection of exhaust, and all original fom factory, ok, today am open all connections and check with water connected at inlet hose.
-
07-28-2007, 09:12 AM #10
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,375
- +1
- 102
See if that exhaust hose is soft, it shouldn't be. And don't run water through the engine without it running. You may fill the engine with water, which would be very bad.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
00 Ultra 150 -- Missing after 10 min -- Help
By jkv1216 in forum Kawasaki Open DiscussionReplies: 12Last Post: 07-04-2016, 07:20 PM -
255 rxpx oil light coming on and beeping sound after 10 min on water. Help!!!
By Renzo778 in forum 4-Tec PerformanceReplies: 8Last Post: 05-08-2016, 01:50 PM -
02 Virage TXi runs bad whe it's been sitting, great after 10 mins. Help plz!!!
By Bigbill55 in forum Polaris Open DiscussionReplies: 1Last Post: 06-27-2011, 11:13 PM -
gp1300r exhaust warning light after 10 min. of riding... Help!!
By rologp in forum Yamaha PWC Performance (2-stroke)Replies: 11Last Post: 01-06-2011, 09:05 PM -
No SPARK, after 10 min of raceng!!!
By xsantia in forum Polaris Open DiscussionReplies: 5Last Post: 09-04-2007, 07:06 PM
Take it to the dealer....
2007 wake 215... one loud beep 4...