Results 1 to 10 of 14
-
07-14-2007, 04:38 PM #1
- Join Date
- Jul 2006
- Posts
- 21
Installed D-Plate, now my warning light is blinking
My stepdad was nice enough to install my D-plate and sensor on my 06 gp1300. As soon as I started the ski, the warning light started blinking with the exhaust temp blinker. I shut it off and turned on a few times, and it would blink right as I turned on the ski. After a few starts, finally it quit going off. Now occasionlly (Every 4 starts or so), it will start beeping right when I turn on the ski. If it doesn't beep right as I start the ski, it doesn't do it at all. Any ideas??
-
07-14-2007, 04:53 PM #2
You installed the chip where the sensor used to be plugged into, right?
-
07-14-2007, 05:10 PM #3
- Join Date
- Jul 2006
- Posts
- 21
-
07-14-2007, 05:21 PM #4
Yours is a 2006, try removing the chip thing and see if it works then.
-
07-14-2007, 09:55 PM #5
- Join Date
- Jul 2006
- Posts
- 1,269
- +1
- 2
He's right, the 06 doesnt need the chip. If it doesnt work right without it you will need to get a resistor from radio shack and solder it in the plug. It's like $1 for a package of 5.
Its been a while since I had to do it so I cant remember if that was a 1k,2k,or 10k ohm. Someone will chime in soon enough if it doesnt work better without the chip.
-
07-14-2007, 10:11 PM #6
My 06' had the same problem,i just plugged the sensor back in.
-
07-15-2007, 08:00 AM #7
- Join Date
- Mar 2007
- Location
- Nashville, TN
- Posts
- 478
-
07-15-2007, 08:27 AM #8
Last edited by XL1200Ltd-Keith; 07-15-2007 at 08:29 AM.
-
07-15-2007, 09:03 AM #9
- Join Date
- Feb 2006
- Posts
- 1,168
- +1
- 25
exhaust sensor
i have a 01 1200r and mine did the same thing yesterday about 2 minutes into the ride,the alarm started sounding and the warning light blinking,,i emediately shut it off !!!! after about 30 seconds it quit,,so i started the ski back up and rode for the rest of the day it never happend again.could`nt figure this one out.i am running double oil though for break in,,i thought maybe all that oil in the exhaust some how gummed up the sensor or somthing,i dunno!!!
-
07-15-2007, 01:29 PM #10
- Join Date
- Jul 2006
- Posts
- 21
Thanks for the help everyone. I really dont know anything about resistors or soldering
. So if I have an 06, I should just take out the chip that came with the D-plate, and plug the sensor back in?
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
pulled my carbs now my oil pump is not pumpimg
By timbo2 in forum Polaris Tech Tips and InfoReplies: 6Last Post: 11-20-2015, 05:39 PM -
warning light is flashing
By 05 green gp in forum Yamaha PWC Performance (2-stroke)Replies: 5Last Post: 06-18-2015, 09:49 AM -
just finished my d-plate now i have an exhaust light
By Horus in forum Yamaha PWC Performance (2-stroke)Replies: 16Last Post: 09-03-2010, 06:22 PM -
just finished my d-plate now i have an exhaust light
By Horus in forum 2-Stroke PerformanceReplies: 3Last Post: 09-03-2010, 12:38 PM -
Now my own family is bustin the sheep jokes!
By WATER WOODY in forum Open DiscussionReplies: 13Last Post: 12-26-2007, 01:19 AM
I bought 2 of these Tera-pumps off Amazon: 1 for fueling and 1 for...
2022 Ultra 310LX-S Owner - Intro...