Page 7 of 7 FirstFirst ... 567
Results 61 to 67 of 67
  1. #61
    override's Avatar
    Join Date
    Jul 2012
    Location
    San Antonio, TX
    Posts
    135
    +1
    7
    So I am about to rebuild my engine and will be adding R & D F/A with ADA 40cc 126psi head and Solas X Prop 13/16 pitch. Anyone have a clue on what specs should I start with on the Mikuni SBN's on this waveventure 760?

    I believe the stock settings are 135 (F)/137.5 (R) HSN and 115 LSN on both. Needle valve is 1.5, couldn't find the stock pop off spring size.


  2. #62
    Hi guys. These are the european stock carv settings. Straight from yamaha. All non USA gp1200rs run these carb specs.
    Main 135
    Pilot 92.5
    HS 1=7/8 2=3/4 3= 7/8
    LS 1 = 1&1/4 2= 1&1/2 3= 1&3/4

  3. #63
    Help needed regarding carb settings on gpr 1200.

    i have read Osidebills recipes regarding settings.

    i have 2 pair of carbs laying here, one with 110 low and 120 main jet, the other one with 92,5 low and 135 jet.

    i have a slight bore ca 1230cc, Riva stinger pipe, no choke, primer pump, Riva flame arrestors.

    Riding temp here in cold Sweden would be 18-30*C (65-85 F)


    Any suggestions?

    /Michael

  4. #64

    Join Date
    Sep 2010
    Location
    Lake Travis, TX
    Posts
    77
    +1
    3
    Quote Originally Posted by Kezmo View Post
    Help needed regarding carb settings on gpr 1200.

    i have read Osidebills recipes regarding settings.

    i have 2 pair of carbs laying here, one with 110 low and 120 main jet, the other one with 92,5 low and 135 jet.

    i have a slight bore ca 1230cc, Riva stinger pipe, no choke, primer pump, Riva flame arrestors.

    Riding temp here in cold Sweden would be 18-30*C (65-85 F)


    Any suggestions?

    /Michael
    Stock 1200 choke plates removed

    110 pilots
    125 mains
    1.5 N&S 95 G springs
    Lows 1 turn out
    Highs 1.5 turns out


    1200 GPR single piper ported or not, Flame arrestors, Advent CDI Yam 84 Engine, No accelerator pump
    Stock, Novi modified, Prok Atomizers or RPM modified (Stock Bore)

    110 Pilots
    120 Mains
    1.5 N/s
    95 Gram Spring


    The above settings seem to be the closest to the lightly modified engine you describe. It might be best to start out with the richer 125 main jet and add 1/4 turn out to the settings recommended above. Remember, with most engines it is better to start rich and work towards a leaner setting than to start lean and blow the engine before you can richen the mixture.

    Good luck,
    Mike

  5. #65
    2002 GP1200r
    It appears to have an aftermarket pipe (A cheap one like the stinger). Removed the choke and installed a primer. Gutted the air box, no restrictions, no baffles, just the cover, no hose running to the bow. Pretty sure this system has no cat converter. Cleaned the carbs.

    What Jets would you recommend? Riding in Kentucky Air temp about 85 Altitude 466. This ski may have some hours on it. Interested in reliability and MPG first and performance 2nd.

  6. #66
    Perhaps you should also a put a forum site on your blog to increase reader interaction.

  7. #67
    Hey guys first post after reading quite a bit.
    I have an 01 XLT with premix, wave eater clips an couplers, stock F/A's, accel pump removed, primer installed, stock jets, needles, seats, springs.
    Just looking for reliability.
    I will be rebuilding the carbs with geuine Mikuni kits. Should I keep the stock jets, needles, seats, springs? If so, how many turns on the hi and low screws?
    If not, what jets, needles, seats, springs do I need for this set up and hi and low screw settings?
    Thank you!

Page 7 of 7 FirstFirst ... 567

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. Replies: 0
    Last Post: 06-18-2015, 05:20 PM
  2. Using Bens jetting specs with non ethanol fuel
    By AusAnton in forum 2-Stroke Performance
    Replies: 14
    Last Post: 04-07-2012, 08:16 PM
  3. For those that have used the warranty...
    By ryanr623 in forum 4-Tec Performance
    Replies: 1
    Last Post: 08-02-2011, 11:58 AM
  4. Jetting specs that I have used
    By Fercho in forum Yamaha PWC Performance (2-stroke)
    Replies: 17
    Last Post: 01-07-2008, 09:21 PM
  5. i need jetting specs on 1300 n/pv with carbs !!
    By RDH in forum Yamaha PWC Performance (2-stroke)
    Replies: 1
    Last Post: 03-27-2007, 09:57 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •