Results 1 to 6 of 6
Thread: EMS display
-
02-15-2006, 03:24 PM #1
EMS display
This is a pretty cool little file telling you what screens are available on the EMS display.
Looks like it's got an integrated boost gauge. Very cool!
-
02-15-2006, 03:31 PM #2
-
02-15-2006, 03:35 PM #3
- Join Date
- Apr 2005
- Location
- sweden
- Posts
- 1,458
- +1
- 17
ems
Racing Display3000LRD LWO050325
Connections
grey cable:
red wire: +12V, should be fused with max. 1A
black wire: Ground, Earth
white wire: TXOUT, transmit data from display
green wire: RXIN, receive data to display
green cables:
compensated thermcouple cables for the high temperature measurement.
Do not plug in or out while voltage is applied!
Operation:
After power-up the display shows some information and the LEDs are flashing. This makes it easy to check
the function of all parts.
The display is equiped with a push button at the front. There are several pages to show, which can be
changed by pressing the button.
Pages:
First page: shows the actual RPM[/min] in large, the throttle position[%] and the 3 temperatures[°C/°F].
Info: The display can show the values for temperature °C/°F and for the pressure in Pa/psi.
To change this setting press the button for more than 2 second while display is in first page.
This setting is internal stored in an EEPROM.
Second page: shows the actual RPM[/min] in large, the 3 ignition angles[°] and the 3 tempeartures[°C/°F].
Third page: shows the RPM[/min] in small, the airpressure[kpa/psi] in large and the 3 temperatures[°C/°F].
Fourth page: show the RPM[/min], the water temperature[°C/°F], the air temperature[°C/°F] and the supply
voltage[V] to the ECU.
Fifth page: shows the limits of RPM[/min], the min and max of the air pressure[kpa/psi], the highest ignition
angles[°] and the highes temperatures[°C/°F].
Info: To reset all limits (same is on page six) press the button for more than 2 second.
Power off and on also clears the limits
Sixth page: shows the actual level of knock sensors[mV] and the RPM[/min] at which the highest knock
level has been and the highest knock levels.
LEDs:
The five LEDs show warnings for water temperature, oil pressure and knock errors for each cylinder.
Info:
If there is no connection to the ECU the display shows an error and the LEDs are flashing!
FOR COMPETITION USE ONLY
No warranty of any engine damage
-
02-15-2006, 09:11 PM #4
- Join Date
- Jan 2006
- Location
- Rydal, Georgia U S A
- Posts
- 3,920
- +1
- 15
WOW
-
02-15-2006, 09:20 PM #5
FINALLY I get to see what that fucken gauge looks like, Ive only owned one for 3 months
-
02-15-2006, 10:04 PM #6
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Rxp gas mileage and fuel display question.
By Mark S in forum 4-Tec PerformanceReplies: 11Last Post: 09-17-2009, 10:02 AM -
My EMS kit came in. Different display?
By Green Hulk in forum 4-Tec PerformanceReplies: 23Last Post: 05-12-2006, 08:30 AM -
What could cause the HOT TEMP display to come on?
By peteshauling in forum 4-Tec PerformanceReplies: 1Last Post: 09-11-2005, 09:40 PM -
smokin em
By PAINKILLER in forum Sea Doo Open DiscussionReplies: 5Last Post: 07-18-2005, 02:18 PM -
maint flashing on display
By Krazy-K in forum 4-Tec PerformanceReplies: 9Last Post: 07-08-2005, 09:23 PM
I’m hoping a new battery emm fresh fuel and oil will get mine going but...
Teej Buys a Jet Ski: 2000 Kawasaki...