Results 1 to 10 of 20
Thread: Wedge bolts?
-
06-24-2007, 12:13 AM #1
- Join Date
- Jun 2007
- Location
- Northeast Georgia
- Posts
- 31
Wedge bolts?
I'm putting a wedge on my Ultra 250X. Where can I get a stainless steel 8X45 bolts from other than Kawasaki? I don't want to order it and have to wait a few days for it. Thanks.
-
06-24-2007, 12:20 AM #2
- Join Date
- May 2007
- Location
- South..South...Florida
- Posts
- 757
i have the wedge on mine and i used the same bolts on from factory!! just make sure you use some loc-tite on the bolts when you put them back up!!!
hope this helps!!!
Good luck
-
06-24-2007, 12:36 AM #3
- Join Date
- Jun 2007
- Location
- Northeast Georgia
- Posts
- 31
-
06-24-2007, 02:35 AM #4
Just go to a Marine supply shop,,,they have them and you only need the longer ones for the bottom bolts.
-
06-24-2007, 10:00 AM #5
factory bolts are too short
You can get galvanized ones at Ace hardware, ss at marine stores.
I wouldn't run that high pressure pump with less than recommended
bolts.
-
06-24-2007, 10:37 AM #6
[quote=tomgtv;321630]You can get galvanized ones at Ace hardware.quote]
Sorry Tom, but that's a bad suggestion for these two reasons:
1. Threads have a certain "class of fit". With the extra Galv, on them, especially into aluminum, you're gonna tear up threads on a very expensive part.
2. Electrolosis and rust - A galv. bolt is just a coated steel bolt.
-
06-24-2007, 11:55 AM #7
- Join Date
- Jun 2007
- Location
- Northeast Georgia
- Posts
- 31
Thank you everyone for the reply.
-
06-24-2007, 02:41 PM #8
Lowes and Ace both should have the SS metric bolts needed at a fraction of what Kawi gets for them.
-
06-24-2007, 02:52 PM #9
Not that it really needs them, but you can find what you are looking for here...
plus any other sst bolt nut or washer.
http://www.boltdepot.com/product.asp...&cm=19&cd=1245
-
06-24-2007, 05:05 PM #10
STOP RUNNING YOURSELF AROUND, just use the bolts that come in the pump you have. Ive been pounding mine and no problems....
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
FS Wedge, VTS extention rod, and bolts
By skoepp in forum Sea Doo ClassifiedsReplies: 4Last Post: 10-08-2009, 08:00 PM -
short pump wedge bolts free
By TxVirageTx in forum Polaris ClassifiedsReplies: 2Last Post: 02-15-2009, 09:32 PM -
add a wedge short pump bolts
By TxVirageTx in forum Polaris ClassifiedsReplies: 0Last Post: 06-28-2008, 08:03 PM -
question on wedge ring bolts for Ultra 250x
By XRIDER in forum Kawasaki PWC Performance (4-stroke)Replies: 2Last Post: 03-26-2007, 05:46 PM -
pump wedge bolts
By shhr in forum Sea Doo Open DiscussionReplies: 1Last Post: 07-06-2006, 09:32 PM
Any suggestions appreciated. Running injector cleaner and doing spark...
2014 310x bog full throttle off...