Results 1 to 4 of 4
  1. #1

    Polaris SLX1200 Rescue

    New to the forum. Based in the UK. Picked up my first ski a couple of months back - a running but very tatty 2000 SLX1200.

    I don't know much about jet skis but am quite experienced with projects of a similar nature having rebuilt a few motorbikes over the years. Not had much to do with 2 strokes either, but again have a bit of understanding from tinkering and reading.

    The ski looks to have had a pretty tough life, but not having seen any others I don't know how it compares to a similar age and hour machine. The hull has got a few marks on the bottom, but no major impacts or damage so hoping that I can repair, fill and re paint the bottom of the hull.

    Engine wise, it starts and runs fine but has been sat for a while. Upon doing a compression test, my PTO cylinder is down on compression (80psi) vs a healthy 130psi in the centre and mag cylinders. So no doubt it will need a top end kit. I suspect the crank seal has gone and it's run lean. Cant be too bad if if still runs on that cylinder though (famous last words).

    I stripped the jet pump off for rebuild and was greeted with some pretty serious carnage. It has the SS 6 vane stator and SS factory wear ring (which looks in reasonable condition) and factory 202 prop on it which has also seen better days.

    As spares over here are non existent, I had a friend of mine repair the chewed up stator and it came out pretty good.

    I also refinished the prop as best I could, although the clearance to the housing is on the larger side. I'm going to remeasure once the stator is all back together and see where we are at. If anyone has a 707 prop in good condition they are willing to ship to the UK, let me know.

    The wear ring is currently stuck on the ski, so any tips on how to remove it would be appreciated!

    Luckily the drivehsaft and impeller shaft are in good condition, despite the seals being complete toast on both. The jet pump was full of water (as I'm sure they all are at this age when not been rebuilt) but luckily the bearings still turned. New ones are on the way, as I ordered 6304 2RS, not realising these were C3 bearings.

    For the impeller shaft I measured the old o rings and ordered some replacements, but not 100% sure if these are right or not. As I needed a new tail cone seal I ordered the OEM parts to compare dimensions. As the OEM ones weren't expensive, I'll fit them and keep the others for spares if they are indeed correct.

    I will need to pull the engine for a rebuild. Also planning toreplace fuel lines/ oil lines and go through everything. All electrical connectors, cables etc to get this thing running sweet and reliably.

    Hope you enjoy the thread.


  2. #2
    Pics below
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	20210711_181708.jpg 
Views:	15 
Size:	151.9 KB 
ID:	478003   Click image for larger version. 

Name:	20210723_135646.jpg 
Views:	12 
Size:	71.8 KB 
ID:	478004   Click image for larger version. 

Name:	20210723_193749.jpg 
Views:	13 
Size:	121.3 KB 
ID:	478005   Click image for larger version. 

Name:	20210725_134942.jpg 
Views:	12 
Size:	68.3 KB 
ID:	478006   Click image for larger version. 

Name:	20210723_135722.jpg 
Views:	12 
Size:	45.5 KB 
ID:	478007   Click image for larger version. 

Name:	20210723_135729.jpg 
Views:	11 
Size:	49.0 KB 
ID:	478008  

    Click image for larger version. 

Name:	20210725_134947.jpg 
Views:	11 
Size:	56.4 KB 
ID:	478009   Click image for larger version. 

Name:	20210725_171855.jpg 
Views:	14 
Size:	48.9 KB 
ID:	478010   Click image for larger version. 

Name:	20210725_180941.jpg 
Views:	14 
Size:	159.4 KB 
ID:	478011   Click image for larger version. 

Name:	20210902_122946.jpg 
Views:	12 
Size:	37.6 KB 
ID:	478012  

  3. #3
    More pics
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	20210902_125640.jpg 
Views:	11 
Size:	47.7 KB 
ID:	478013   Click image for larger version. 

Name:	IMG-20210817-WA0000.jpg 
Views:	12 
Size:	60.8 KB 
ID:	478014  

  4. #4
    Nice one mate canít wait to see the end of it

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Polaris Slx1200 tick
    By northman in forum Polaris Tech Tips and Info
    Replies: 9
    Last Post: 10-17-2017, 07:48 PM
  2. 2000 Polaris SLX1200 MFD issue
    By northman in forum Polaris Open Discussion
    Replies: 2
    Last Post: 07-06-2017, 08:21 PM
  3. 98 GP800 or 2000 polaris slx1200
    By dremmick in forum Yamaha PWC Performance (2-stroke)
    Replies: 16
    Last Post: 03-08-2016, 09:53 PM
  4. 01 polaris slx1200
    By polarisman01 in forum Polaris How To & FAQs
    Replies: 51
    Last Post: 07-19-2013, 04:35 PM
  5. 2001 SLX1200 polaris no fire
    By rb8179 in forum Polaris Open Discussion
    Replies: 1
    Last Post: 07-02-2010, 10:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •