Page 1 of 2 1 2 LastLast
Results 1 to 10 of 13
  1. 06-21-2007, 11:03 PM #1
    hitman
    hitman is offline
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    13

    dumb carb question

    How do I get the throttle and choke linkages off the carbs on my 99 GP1200? I believer they are the Mikuni Super BN44s.

    Sorry for the dumb question.
    Reply With Quote Reply With Quote

  2. 06-21-2007, 11:13 PM #2
    OsideBill
    OsideBill is offline
    Moderator OsideBill's Avatar
    Join Date
    Mar 2006
    Location
    United States
    Posts
    11,875
    +1
    34
    loosen the jam nut at the adjuster and the cable assembly will come out of the mounting bracket then align the cable to the slot in the throttle pulley and the cable end should just slide right out. If you need a service manual go to this link and download one for your ski

    http://www.greenhulk.net/forums/showthread.php?t=9546

    Reply With Quote Reply With Quote
  3. 06-21-2007, 11:16 PM #3
    dav_dman
    dav_dman is offline
    Dave Sharp dav_dman's Avatar
    Join Date
    Aug 2005
    Location
    louisville Ky/so. IN
    Posts
    1,453
    +1
    1
    you pop 'em right off. pry 'em and they'll pop off.

    i think he's talking about the linkage rods, Bill.
    Reply With Quote Reply With Quote
  4. 06-21-2007, 11:16 PM #4
    hitman
    hitman is offline
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    13
    Quote Originally Posted by osidebill View Post
    loosen the jam nut at the adjuster and the cable assembly will come out of the mounting bracket then align the cable to the slot in the throttle pulley and the cable end should just slide right out. If you need a service manual go to this link and download one for your ski

    http://www.greenhulk.net/forums/showthread.php?t=9546

    Sorry, I meant I already have the carbs out and am trying to separate all three to rebuild them. I have to disconnect the the sync arms that connect all three carbs. Do I just loosen the nut on each?
    Reply With Quote Reply With Quote
  5. 06-21-2007, 11:19 PM #5
    OsideBill
    OsideBill is offline
    Moderator OsideBill's Avatar
    Join Date
    Mar 2006
    Location
    United States
    Posts
    11,875
    +1
    34
    No Like Dave said pop them off they snap over the ball ends use a screwdriver
    Reply With Quote Reply With Quote
  6. 06-21-2007, 11:22 PM #6
    hitman
    hitman is offline
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    13
    OK. I was afraid to pry on them but I got it. Thanks guys.
    Reply With Quote Reply With Quote
  7. 06-21-2007, 11:33 PM #7
    hitman
    hitman is offline
    hitman's Avatar
    Join Date
    Aug 2006
    Location
    Ft. Lauderdale, FL
    Posts
    4,328
    +1
    13
    One last one. Aren't I supposed to lube a few of rebuild pieces with 100% silicone spray?
    Reply With Quote Reply With Quote
  8. 06-22-2007, 07:50 AM #8
    97GPSLEEPER
    97GPSLEEPER is offline
    DAGO RACING CREW 97GPSLEEPER's Avatar
    Join Date
    Apr 2006
    Location
    Orange, TX
    Posts
    4,239
    +1
    171
    I have never lubed any internal carb parts, and I have never heard of anyone doing it.
    Reply With Quote Reply With Quote
  9. 06-22-2007, 07:56 AM #9
    Duke
    Duke is offline
    Duke's Avatar
    Join Date
    Jul 2006
    Location
    Florida
    Posts
    10,004
    +1
    407
    Quote Originally Posted by hitman View Post
    One last one. Aren't I supposed to lube a few of rebuild pieces with 100% silicone spray?
    Nothing internal, Pack the springs on the adjuster srews with lithium grease to prevent corrosion. Silicone all the throttle shaft bushings and I always put antiseeze on the idle adjustment screw threads.
    Reply With Quote Reply With Quote
  10. 06-22-2007, 08:00 AM #10
    RX951
    RX951 is offline
    Moderator RX951's Avatar
    Join Date
    Apr 2005
    Location
    League City, Texas
    Posts
    16,074
    +1
    25
    Quote Originally Posted by hitman View Post

    Sorry for the dumb question.

    * no question is dumb....whether it is a veteran or newbie

    * we ask because we don't know.

    * I would expect every and anyone to ask questions on this forum so education can continue

    * this forum is great !

    Fire away with any question you have Hitman !!
    Reply With Quote Reply With Quote
Page 1 of 2 1 2 LastLast
« Hello Derek | Factory Yamaha race hull info »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Dumb Carb Question..
    By raptorobbie in forum 2-Stroke Performance
    Replies: 1
    Last Post: 08-22-2014, 12:30 PM
  2. dumb carb question??????
    By sullified in forum Polaris Open Discussion
    Replies: 3
    Last Post: 07-14-2008, 02:49 PM
  3. dumb carb question
    By airbornexp in forum 2-Stroke Performance
    Replies: 25
    Last Post: 11-14-2007, 06:20 PM
  4. carb question for 800
    By ozzygp in forum Yamaha PWC Performance (2-stroke)
    Replies: 4
    Last Post: 09-13-2006, 02:38 AM
  5. STOCK CARB QUESTION
    By Tommy Gun in forum Yamaha PWC Performance (2-stroke)
    Replies: 2
    Last Post: 06-28-2006, 10:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules