Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21
  1. #11

    Join Date
    Apr 2007
    Location
    Surprise, AZ via NorCal
    Posts
    236
    +1
    26
    I had my stock plate reworked by Groupk years ago when they first offered the service. It didn't provide much improvement over stock. Better off spending $ on an aftermarket impeller/sponsons. An STX-R rideplate is much better, but you lose reverse. Sometimes these pop-up on eBay.
    Quote Originally Posted by Kawachris View Post
    I will check it out asap. Has anyone done the ride plate mod? I just read about it on groupk. I guess it is a plate you put above the jet pump somewhere and it is supposed to lift the front of the boat. With a full tank of gas and going slow, the trim on the front of the hull is under water.

  2. #12
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3
    So here's what happened, I swapped the jet pump with the the jet pump from the 02 parts ski. The ski that I ride really woke up. I now have less vibration at lower speeds, and it pulls allot harder it even hit 56 mph via dream-o-meter. Really excited! Maybe in the off season I will pull it back out and rebuild the bearings, possibly put a solas impeller in if I can find a cheap enough one.

    Thanks for all the help fellas, really appreciate it

  3. #13
    I have an stxr ride plate i can let go for cheap

  4. #14
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3
    How much? I kind of like Reverse is there a way of rigging it in there ?

  5. #15

    Join Date
    Apr 2007
    Location
    Surprise, AZ via NorCal
    Posts
    236
    +1
    26
    You would need a set of custom fab'd mounts for the bucket. Not worth the effort.
    Quote Originally Posted by Kawachris View Post
    How much? I kind of like Reverse is there a way of rigging it in there ?

  6. #16
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3
    I will be keeping it stock it's still fun enough for me

  7. #17
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3
    After riding with the parts ski jet pump for two weeks, my problem has reoccurred. I am back down to 45 mph, I thought I would get at least the season out of the back up pump.
    I am assuming I'm in need of a pump rebuild, what's a good place to send it to? I've never had to deal with something like this so any input would be greatly appreciated.

  8. #18
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3
    So I know this thread was a while back but I finally got around to rebuilding the jet pump on my stx di. I am just having a hard time figuring out where that little cone shaped spacer goes. Does anyone know what I’m talking about and could help.


  9. #19
    steve45's Avatar
    Join Date
    Feb 2008
    Location
    Texas
    Posts
    8,148
    +1
    837
    I don't remember a cone-shaped spacer. Have you looked at the parts diagram?

    https://partsfinder.onlinemicrofiche...asakipwc&a=128

  10. #20
    Kawachris's Avatar
    Join Date
    May 2020
    Location
    New Hampshire
    Posts
    75
    +1
    3

    Stx 1100 di running at 41mph

    Quote Originally Posted by steve45 View Post
    I don't remember a cone-shaped spacer. Have you looked at the parts diagram?

    https://partsfinder.onlinemicrofiche...asakipwc&a=128
    I just had a look and it looks like it goes in between the seal and snap ring i just don’t remember which direction.

    part number 92028

    Btw that diagram is awesome

    Easy issue has been resolved I just had to take another look. The smaller side of the bushing goes towards the impeller. Thanks again
    Last edited by Kawachris; 02-27-2021 at 01:50 PM.

Page 2 of 3 FirstFirst 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Stx 1100 di running hot
    By Kawachris in forum Kawasaki PWC Performance (2-stroke)
    Replies: 15
    Last Post: 06-01-2020, 03:52 PM
  2. Stx 1100 di running hot
    By Kawachris in forum Kawasaki PWC Performance (4-stroke)
    Replies: 10
    Last Post: 05-30-2020, 02:38 PM
  3. So got the new motor running today 97 stx 1100
    By duty in forum Kawasaki How To & FAQs
    Replies: 1
    Last Post: 08-26-2017, 04:21 PM
  4. Stx 1100 running too rich
    By NCrunner2012 in forum Kawasaki PWC Performance (2-stroke)
    Replies: 7
    Last Post: 06-12-2016, 02:19 PM
  5. Flushing a 97 1100 STX, does it have to be running?
    By sbklf in forum Kawasaki Open Discussion
    Replies: 6
    Last Post: 01-20-2011, 07:59 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •