Page 1 of 3 123 LastLast
Results 1 to 10 of 27
  1. #1
    DanSVHO's Avatar
    Join Date
    Jul 2015
    Location
    Delray Beach, FL
    Posts
    772
    +1
    87

    Stage 3 2019 Fx...slow ;(

    Just installed the following parts
    -riva ribbon removal
    -riva power filter kit
    -pump wedge
    -engine breather
    -fizzle with dedicated line and cooling to
    anode
    -stage 3 deans tune
    -riva retainers
    -deans ride plate

    i donít know how accurate the stock tach is but Iím only seeing 8200
    and GPS speed is 75.4 mph solas 13/18 is going in soon but I doubt thatís going to give me 8-10 mph. Funny thing is the stock speedo used to go to 69-70 now it only goes to 55. Deans says even with stock prop I should be 80 mph all day with a full tank. No charge pipes are loose and no exhaust leaks. Not sure what else to check. Leaking from where I tapped plastic manifold? Or where I used the hole saw on manifold? I have the rubber orange o ring from the manifold to throttle body is that supposed to go back in somewhere?


  2. #2

  3. #3
    xkon's Avatar
    Join Date
    Jun 2017
    Location
    NJ
    Posts
    130
    +1
    24
    Quote Originally Posted by DanSVHO View Post
    Just installed the following parts
    -riva ribbon removal
    -riva power filter kit
    -pump wedge
    -engine breather
    -fizzle with dedicated line and cooling to
    anode
    -stage 3 deans tune
    -riva retainers
    -deans ride plate

    i don’t know how accurate the stock tach is but I’m only seeing 8200
    and GPS speed is 75.4 mph solas 13/18 is going in soon but I doubt that’s going to give me 8-10 mph. Funny thing is the stock speedo used to go to 69-70 now it only goes to 55. Deans says even with stock prop I should be 80 mph all day with a full tank. No charge pipes are loose and no exhaust leaks. Not sure what else to check. Leaking from where I tapped plastic manifold? Or where I used the hole saw on manifold? I have the rubber orange o ring from the manifold to throttle body is that supposed to go back in somewhere?
    The paddle wheel sensor is always inaccurate. It probably was made worse when the ride plate was changed. The rubber o ring is not reused.

  4. #4
    DanSVHO's Avatar
    Join Date
    Jul 2015
    Location
    Delray Beach, FL
    Posts
    772
    +1
    87
    There isn’t a paddle wheel anymore. I actually wish it was still that! New one uses rpm and engine load to calculate speed displayed on the screen.
    Quote Originally Posted by xkon View Post
    The paddle wheel sensor is always inaccurate. It probably was made worse when the ride plate was changed. The rubber o ring is not reused.

  5. #5
    outnumbered's Avatar
    Join Date
    May 2007
    Location
    Locust NC
    Posts
    810
    +1
    136
    It almost sounds like your ski isn't recognizing the tune.

  6. #6
    callmeEarl's Avatar
    Join Date
    May 2019
    Location
    DeLaWaRe
    Posts
    40
    +1
    1
    ....

  7. #7
    DanSVHO's Avatar
    Join Date
    Jul 2015
    Location
    Delray Beach, FL
    Posts
    772
    +1
    87
    Exactly. It reads 8200 on dash but dean said it should be 8600 even with the stock prop. The fact that the Speedo is weird makes me thing it’s something to do with the ecu and ski mating. I will disconnect battery and un install ecu. And redo the calibration process and see of that helps. Do you know if the orange o-ring on stock Manifold to throttle body gets discarded or reinstalled? I didn’t do it because there wasn’t a place for it but maybe I fudged and it goes somewhere.

  8. #8
    outnumbered's Avatar
    Join Date
    May 2007
    Location
    Locust NC
    Posts
    810
    +1
    136
    I'm not sure about the o-ring, but it is mentioned above that it isn't needed. However, I still think your issue is recognition of the tune.

  9. #9
    So with the (FACT) there is a speed limiter on our 19's? If so i would need to spend $500 just to remove speed limiter? What is top speed with a intake filter & riva plate?

  10. #10
    DanSVHO's Avatar
    Join Date
    Jul 2015
    Location
    Delray Beach, FL
    Posts
    772
    +1
    87
    No, $160 for speed limiter removal

    Dean's Team 'Speed Limit Control' ECU Performance Tune for Yamaha Waverunners

    Send in your ECU for a Reflash to remove the factory speed limit control and gain 3-4 mph with no additional upgrades. Easily increase top speed...
    DeanSLC $160.00


Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Fx svho 2019 stage 1 plus
    By MARCO PESSOA in forum Yamaha PWC Performance (4-stroke)
    Replies: 4
    Last Post: 05-30-2019, 07:30 AM
  2. Athena/Riva stage 2 to slow ????
    By idoodou in forum 4-Tec Performance
    Replies: 30
    Last Post: 05-04-2014, 06:35 AM
  3. 05 RXP STAGE 2 going to slow
    By JOSE13RT in forum 4-Tec Performance
    Replies: 23
    Last Post: 08-05-2006, 09:54 AM
  4. Slow RXP Riva Stage 2
    By idizzy in forum 4-Tec Performance
    Replies: 11
    Last Post: 07-13-2006, 03:53 PM
  5. stage 1 RXT numbers, is this slow???
    By waverider in forum 4-Tec Performance
    Replies: 27
    Last Post: 04-09-2006, 08:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •