Results 1 to 10 of 15
Thread: pro 1200 display
-
06-07-2007, 02:36 AM #1
- Join Date
- Jun 2007
- Posts
- 65
pro 1200 display
Hi Guys,
I have just been trying to sort the Carb problem out (see thread below) and I noticed my display unit is not working, I am not having a good time at the moment.
It was working fine then suddenly cut out, is there a fuse that relates to the display and could anyone tell me where to find it.
If the display doesn,t work will my trim and bildge still work.
Is the display cutting out a common fault, it has worked fine for three years but I have been cranking the ski over alot lately due to me putting alot of fogging oil in it.
Thanks,
Danny.
-
06-07-2007, 06:10 AM #2
- Join Date
- Aug 2006
- Location
- Homer Glen Il.
- Posts
- 8,777
- +1
- 123
Danny ,
there is a 1/4 fuse in your eletrical box for the display open it up and check it out .
-
06-07-2007, 01:24 PM #3
- Join Date
- Jun 2007
- Posts
- 65
Thanks for the reply,
I have taken the fuse out, I think it hasn't blown its so small its hard to tell, is there any other fault it could be that you know of.
Thanks,
Danny
-
06-07-2007, 01:32 PM #4
- Join Date
- Aug 2006
- Location
- Homer Glen Il.
- Posts
- 8,777
- +1
- 123
pretty sure if it's not the fuse it's a bad mfd .try putting another fuse in there or a jumper across it for a split second and see if it comes on . or take an ohm meter and check to see if your fuse is good
-
06-07-2007, 01:33 PM #5
- Join Date
- Jun 2007
- Posts
- 65
Thanks for the reply,
I have taken the fuse out, I think it hasn't blown its so small its hard to tell, is there any other fault it could be that you know of.
Thanks,
Danny
-
06-07-2007, 01:44 PM #6
- Join Date
- Jun 2007
- Posts
- 65
Forgot to ask,
does the trim and bilge pump work if the MFD doesn't work.
Danny.
-
06-07-2007, 01:51 PM #7
- Join Date
- Aug 2006
- Posts
- 1,236
Danny, did you check both fuses?
-
06-07-2007, 01:57 PM #8
- Join Date
- Jun 2007
- Posts
- 65
Hi Wetherby,
I have checked both fuses the 3amp looks fine, but the 1/4fuse its hard to tell if its blown, but it was corroded at each end.
I have cleaned the fuse up, I can't think of anything else it could be?
Danny
-
06-07-2007, 01:59 PM #9
Check under your electrical board for rust. If rusted replace.
-
06-07-2007, 02:01 PM #10
- Join Date
- Jun 2007
- Posts
- 65
Okay will check to see if rusted.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
MFD display on Pro 1200 does not work
By FX-1 in forum Polaris Open DiscussionReplies: 1Last Post: 03-23-2015, 05:02 PM -
WTB - Parts WTB throttle lever, multi function display and cdi for pro 1200
By skoolball23 in forum Polaris ClassifiedsReplies: 1Last Post: 07-26-2012, 08:47 PM -
2001 - Pro 1200 - MFD Display Issue
By elwayisgod in forum Polaris Open DiscussionReplies: 2Last Post: 07-14-2009, 08:26 PM -
Wanted MFD display - Pro 1200
By LiquidPro1200 in forum Polaris ClassifiedsReplies: 1Last Post: 08-13-2008, 12:22 PM -
Rius takes pro 1200 world title in Havascrew...
By 11 in forum Race Events and NewsReplies: 32Last Post: 10-20-2005, 11:58 PM
Damn haha all righty I just ordered another wear ring. It was weird I was...
Frankenstein Exhaust overheating...