Results 1 to 10 of 11
-
06-06-2007, 12:18 PM #1
- Join Date
- May 2007
- Posts
- 37
Should Supercharger Wheel Turn????
SHOULD YOU BE ABLE TO TURN THE SPERCHARGER WHEEL COUNTERCLOCKWISE????I INSTALL NEW METAL WASHERS AND REINSTALL SC AND IF I REACH INSIDE AND WITH A GOOD AMOUNT OF FORCE I CAN TURN THE WHEEL COUNTER-CLOCK-WISE ALITTLE!!! IS THIS NORMAL???
-
06-06-2007, 12:26 PM #2
- Join Date
- Jul 2005
- Location
- euxton nr chorley lancashire, england
- Posts
- 1,500
- +1
- 2
-
06-06-2007, 12:28 PM #3
It Should Not Spin At All, Should Click Back And Forth A Little..
-
06-06-2007, 12:46 PM #4
- Join Date
- May 2007
- Posts
- 37
So If It Moves What Does That Mean??? It Did It Before And The Ski Performed Bad At Crusing Speed And When You Went To Wot It Had Low Boost For A Few Sens. And Then Pick Up And Ran Normal.. So I Thought The Washers Were Slipping.. So I Just Replace Them And Crankit Up And After Shooting It Off With Some Force It Turn Ccw Alittle... So What Is My Problem Now Do Yall Thing?????
-
06-06-2007, 12:48 PM #5
Incorrect Installation Of Clutch Maybe...not Sure.
-
06-06-2007, 01:09 PM #6
I would think with lots of force you will be able to turn the whole motor around....so, what's you definition of "some force".?
-
06-06-2007, 01:37 PM #7
What washers did you replace? Did you add new spring washers as well? The spring washers set the tension. If you reused the old ones, new clutch washers wont make it tight...
-
06-06-2007, 01:41 PM #8
- Join Date
- May 2007
- Posts
- 37
I MEAN I HAVE TO TURN ABOUT AS HARd as i can with my hand to make it move!!! how would i know if the entire motor is moving or not???
-
06-06-2007, 01:48 PM #9
On a fresh, properly setup supercharger, installed and on the motor, you CAN put your hand on the impeller blades and 'turn' it a little bit ... there is a little 'slop' or movement, but it will NOT go very far if setup properly. I too was surprised to find that the SC impeller will turn a very short distance ... but it is NOT slipping, just moving a little due to very slight gear drive/motor movement. If you can turn the SC impeller a little bit, then it stops, that is normal.
-
06-06-2007, 02:01 PM #10
you would be able to turn it a bit but not much... even if you did this with the impeller you would be able to turn it a bit also .. but you would never be able to turn the engine..did you check the clutch slippage after installation of the washers?
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
I can turn the supercharger wheel by hand
By ARCTIC in forum 4-Tec PerformanceReplies: 24Last Post: 07-12-2011, 06:40 PM -
which supercharger wheel?
By dave911rsr in forum 4-Tec PerformanceReplies: 3Last Post: 03-15-2008, 04:35 PM -
Rive Pro Series Supercharger Wheel on GTX SC?
By dochere195 in forum 4-Tec PerformanceReplies: 5Last Post: 07-17-2007, 10:36 PM -
Best supercharger wheel?? Green wheel??
By codymouse54321 in forum 4-Tec PerformanceReplies: 18Last Post: 07-05-2007, 08:16 PM -
what rpms should i be turning?
By ebarfool in forum Yamaha PWC Performance (2-stroke)Replies: 3Last Post: 05-19-2007, 01:52 PM
Yeah I think I will save that for something to do during the winter...
Frankenstein Exhaust overheating...