Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1

    Question 2010 rxt-x ibr brackets

    Can anyone link me to the updated ibr brackets for my ski? I have searched the forum and I have seen people talk about them but I canít aeek to find them or a part number. I had the dreaded spinning in plastic issue when trying to take mine off over the weekend and I want to make sure I replace it with the updated part. I have seen a lot of posts of bout leaking brackets and whatnot so I just want to get it done


  2. #2
    No one ? I thought this was a thing with these skis

  3. #3
    EVN81's Avatar
    Join Date
    Jul 2013
    Location
    Terschelling - the Netherlands
    Posts
    652
    +1
    59

    2010 rxt-x ibr brackets

    From 2013 and up they were updated if Iím correct. Compare the P/N in the partsfinder catalogue.

    But you have the rideplate mounted pump with cooling water supply next to / under the iBr motor. So thereís a big hole in the hull whatís sealed by the portside (leftside).

    From 2012 and on the pump changed back to the hull and so did the cooling water supply.

    Long story short you might be stuck with the crappy plastic with the molded nuts.

    However you make only once the mistake to use Loctite or apply the mentioned torque.

    Just little grease handtight and then a little snug with spanner. Never came loossen as I check that area regular.

    If your busy with it why not update to the hull mounted jetpump

  4. +1 by:


  5. #4
    Hi , does someone knows what is the part number to upgrade the plastic ibr bracket and the exhaust plastic bracket on a 2010 rxt 260 ?

    Thank you and best regards ,

  6. #5
    There isn’t one just use new 2010 stuff works fine

  7. #6
    T3H_Hott's Avatar
    Join Date
    May 2019
    Location
    SFL
    Posts
    10
    Are you guys talking about the plastic part where the IBR module bolts up to? Or the updated bucket in the pump tunnel?

  8. #7
    The plastic triangle things

  9. #8

    Join Date
    Aug 2013
    Location
    Connecticut
    Posts
    118
    +1
    23
    The part number for the left side is 268000133 and the right side would be 268000135 the brackets have been updated so the spinning brass nut problem should not happen again with proper torque on the bolts

  10. #9
    EVN81's Avatar
    Join Date
    Jul 2013
    Location
    Terschelling - the Netherlands
    Posts
    652
    +1
    59
    This is 268000133.
    As said, there is no updated bracket for 2010/2011 models

    Click image for larger version. 

Name:	IMG_3075.jpg 
Views:	21 
Size:	84.9 KB 
ID:	456455

  11. #10
    Thank you so much mates

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2010 RXT 260 IBR faults when hitting waves
    By rinus in forum 4-Tec Performance
    Replies: 8
    Last Post: 07-29-2018, 12:49 PM
  2. Seadoo RXT 260, 2010 IBR fault
    By rinus in forum 4-Tec Performance
    Replies: 8
    Last Post: 07-09-2018, 08:11 PM
  3. 2010 rxt ibr/pump fixing plates
    By BEECHFRONT in forum 4-Tec Performance
    Replies: 6
    Last Post: 06-26-2014, 02:54 AM
  4. Anyone with older iBR skis (2009-2010) having iBR issues?
    By SCHNORR12 in forum 4-Tec Performance
    Replies: 5
    Last Post: 04-05-2014, 08:59 PM
  5. Replies: 16
    Last Post: 08-07-2013, 03:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •