Results 1 to 10 of 10
  1. 06-04-2007, 06:34 PM #1
    Hoovermaneuver
    Hoovermaneuver is offline
    Texas Hoovermaneuver's Avatar
    Join Date
    Apr 2005
    Location
    Fort Worth, Texas
    Posts
    840
    +1
    29

    SC homemade tool

    What size wrench do you grind down to take off the nut on the SC to change the washers? I saw it somewhere but now that I need to make one I can't find it.
    Reply With Quote Reply With Quote

  2. 06-04-2007, 07:14 PM #2
    The Bandit
    The Bandit is offline
    Moderator The Bandit's Avatar
    Join Date
    Jul 2006
    Location
    Wilmette, IL
    Posts
    8,331
    +1
    1
    1 inch wrench
    Reply With Quote Reply With Quote
  3. 06-04-2007, 07:38 PM #3
    Hoovermaneuver
    Hoovermaneuver is offline
    Texas Hoovermaneuver's Avatar
    Join Date
    Apr 2005
    Location
    Fort Worth, Texas
    Posts
    840
    +1
    29
    TY
    Reply With Quote Reply With Quote
  4. 06-05-2007, 09:16 AM #4
    North49
    North49 is offline
    Join Date
    Jun 2005
    Location
    Hamilton, Ontario, Canada
    Posts
    556
    I used a 24mm wrench and grinded it down thin enough. Found it fit perfect. I have the SC tool iteself but found after a few uses it just bends too easily now, to the point where I cannot use it. I was in a jam and needed something immediately. Used a digital micrometer to measure the SC retaining washer and then went searching through the tool box. 1 inch was a little too big and 24mm was a snug fit.
    Reply With Quote Reply With Quote
  5. 06-05-2007, 01:37 PM #5
    Green Hulk
    Green Hulk is offline
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    38,179
    +1
    3,239
    believe it or not the 4-tecperformance hardened tools are almost ready
    Reply With Quote Reply With Quote
  6. 06-05-2007, 01:50 PM #6
    North49
    North49 is offline
    Join Date
    Jun 2005
    Location
    Hamilton, Ontario, Canada
    Posts
    556
    Quote Originally Posted by Green Hulk View Post
    believe it or not the 4-tecperformance hardened tools are almost ready
    I had a feeling you would have something in the works, relating to this.
    Reply With Quote Reply With Quote
  7. 06-05-2007, 02:14 PM #7
    SeanCucf
    SeanCucf is offline
    I'm kind of a big deal SeanCucf's Avatar
    Join Date
    Jul 2006
    Location
    Oldsmar, FL
    Posts
    1,849
    Quote Originally Posted by Green Hulk View Post
    believe it or not the 4-tecperformance hardened tools are almost ready
    hmm....your toying with me......in that case can you throw one back on my order if they're around when the green wheels are in?
    Reply With Quote Reply With Quote
  8. 06-05-2007, 02:30 PM #8
    The Bandit
    The Bandit is offline
    Moderator The Bandit's Avatar
    Join Date
    Jul 2006
    Location
    Wilmette, IL
    Posts
    8,331
    +1
    1
    my 1 incher really satisfies...
    Reply With Quote Reply With Quote
  9. 06-05-2007, 03:26 PM #9
    Jeff C
    Jeff C is offline
    Resident Jicky Jack Jeff C's Avatar
    Join Date
    May 2005
    Location
    Twin Cities, MN
    Posts
    1,153
    +1
    2
    Quote Originally Posted by RXP Steve View Post
    my 1 incher really satisfies...

    That's sort of sad don't you think?
    Reply With Quote Reply With Quote
  10. 06-05-2007, 04:01 PM #10
    The Bandit
    The Bandit is offline
    Moderator The Bandit's Avatar
    Join Date
    Jul 2006
    Location
    Wilmette, IL
    Posts
    8,331
    +1
    1
    Quote Originally Posted by Jeff C View Post
    That's sort of sad don't you think?
    I have done S/C's four times so far with this wrench, whats so sad about it? huh? WTF you talkin bout?! huh?
    Reply With Quote Reply With Quote
« mmi marine programs | Anybody in Ft.Lauderdale W/ Prop spline tool »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. SC'er tool in tampa/clearwater??
    By SeanCucf in forum Southeast
    Replies: 0
    Last Post: 07-19-2007, 12:47 AM
  2. SC'er tool in tampa/clearwater??
    By SeanCucf in forum Sea Doo Open Discussion
    Replies: 0
    Last Post: 07-19-2007, 12:44 AM
  3. Stage III SC Install Tools
    By KiwiRXP in forum 4-Tec Performance
    Replies: 6
    Last Post: 01-03-2007, 07:16 PM
  4. Tools for removing SC'r
    By SeaDoocer in forum 4-Tec Performance
    Replies: 13
    Last Post: 10-01-2006, 10:38 AM
  5. Simple homemade water extraction tool
    By CrazyA in forum Yamaha How To & FAQs
    Replies: 2
    Last Post: 08-13-2006, 08:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules