Results 1 to 8 of 8
Thread: Another MFD?
-
06-03-2007, 11:25 PM #1
Another MFD?
I know everyone says use a 1/4 amp fuse and even had to go back in the tech section to double check what I read.
But In my Clymer on page 84 on bottom right corner it says
"b. Check the condition of the 4 amp fuse"
I just wanted to double check cause 1/4 to 4 amp is a big differeance. I got an MFD coming cause the one on mine was bad. Voltage to connecter was good but I guess the previous owner stuck a 20amp fuse in it.
Just dont want to blow this MFD Im waiting on the recieve.
Thanks,
Ron
-
06-03-2007, 11:43 PM #2
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,373
- +1
- 102
Mine inside the box is 1/4A. Maybe it was a typo?
-
06-03-2007, 11:44 PM #3
-
06-03-2007, 11:46 PM #4
Must have been a typo like xlint says. When I say it I was like wtf.
Thanks for clearing that up for me.
Also to make sure Im looking at the right spot. It the fuse at the R/Pur area correct.
Last edited by rfjr23; 06-03-2007 at 11:51 PM.
-
06-03-2007, 11:56 PM #5
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,373
- +1
- 102
Open the box for positive identification. There should be only 2 fuses inside. Check them both and replace if necessary.
-
06-03-2007, 11:58 PM #6
Ill have to look in the morning as I dont keep it here. But I only seen one bus type fuse and it was a 20amp fuse.
Am I looking at the wrong one?
94 sl 750
Im gonna have to take a pic now. lol
I know I got the proper voltage to it but I didnt check the voltage after I took the fuse. Didnt even think about it. Hope I didnt buy an extra mfd.
edit** Im looking through the wiring diagram in my Clymer manual and by this it is the correct fuse but in the MFD troubleshooting section it also states 4 amp. Previous owner had a 20 which would explain why it dont work now. So Ill have to get a 1/4 amp fuse and wait for new MFD.
Thanks for the helpLast edited by rfjr23; 06-04-2007 at 12:04 AM.
-
06-04-2007, 12:24 AM #7
- Join Date
- Oct 2006
- Location
- Cleveland OH
- Posts
- 18,373
- +1
- 102
It is the one that goes from R/Ppur to R/Pur.
-
06-04-2007, 09:19 AM #8
I just replaced the MFD fuse in both my ski's and they started working again. They were both 1/4amp as my Clymer manual stated. I don't remember the page you scanned. I think it was on a different page. I bought the fuses from Radio Shack along with some extras. I only saw two fuses in my electric box. The other was a 3 amp.
Edit: Nevermind I have the 96-99 manual.Last edited by rickreeves1; 06-04-2007 at 09:23 AM.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Towing the RXP with another boat??
By Gforce in forum 4-Tec PerformanceReplies: 7Last Post: 07-24-2018, 12:15 PM -
Anyone looking for a used RXP? +another ski & trailer?
By Jeff C in forum Sea Doo Open DiscussionReplies: 3Last Post: 03-09-2017, 06:45 PM -
Thread jump from another website.. I lost my MFD mode button seeking replacement...
By jcc011185 in forum Polaris Open DiscussionReplies: 16Last Post: 09-22-2006, 07:02 PM -
Lost ANOTHER clutch today!
By Green Hulk in forum 4-Tec PerformanceReplies: 13Last Post: 07-04-2005, 12:50 PM -
Another happy RR IC customer!
By rx4pain in forum 4-Tec PerformanceReplies: 6Last Post: 06-30-2005, 10:00 PM
It does not matter what way. I had 2008 GTX LTD 215 and had mine go out a...
Main Relay direction (not starter...