Results 1 to 5 of 5
  1. 05-30-2007, 06:41 PM #1
    slugo10
    slugo10 is offline
    slugo10's Avatar
    Join Date
    Jan 2006
    Location
    Gulfport, MS
    Posts
    49

    ? about metal washers...

    I ordered the metal washers from Jerry yesterday. My question is does it matter the order of the washers on the install? Are they both the same size or is there an outer and inner washer. Also what is the best way to remove the gear without loosing the needle bearings?
    Reply With Quote Reply With Quote

  2. 05-30-2007, 07:02 PM #2
    Green Hulk
    Green Hulk is offline
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    38,831
    +1
    3,396
    The washers will only go on one way so you can't go wrong. One has a smaller hole than the other.

    Carefully pull the gear off and if you get lucky half the needle bearings will stay in the gear. Carefully put it back on the shaft and then feed the ones that dropped out one by one.
    Reply With Quote Reply With Quote
  3. 05-30-2007, 07:06 PM #3
    jetskibill9999
    jetskibill9999 is offline
    Join Date
    Jul 2005
    Location
    euxton nr chorley lancashire, england
    Posts
    1,500
    +1
    2
    Quote Originally Posted by Green Hulk View Post
    The washers will only go on one way so you can't go wrong. One has a smaller hole than the other.

    Carefully pull the gear off and if you get lucky half the needle bearings will stay in the gear. Carefully put it back on the shaft and then feed the ones that dropped out one by one.
    jerry what kind of metal are these washers? mild steel?
    Reply With Quote Reply With Quote
  4. 05-30-2007, 07:47 PM #4
    Green Hulk
    Green Hulk is offline
    Site Admin Green Hulk's Avatar
    Join Date
    Apr 2005
    Location
    Morgan City, LA
    Posts
    38,831
    +1
    3,396
    ubotitanium
    Reply With Quote Reply With Quote
  5. 05-30-2007, 07:54 PM #5
    JFizzleJR
    JFizzleJR is offline
    JFizzleJR's Avatar
    Join Date
    Aug 2005
    Location
    FL
    Posts
    8,830
    +1
    965
    hmm I always thought it was plutonium-238?




    Just Kidding Bill
    Reply With Quote Reply With Quote
« 7/16 drill bit dropped into hull | Lost a few RPM's ? »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. About Superchargers: Inherent Flaws and Preventing Failure with Metal Washers
    By Shibby1485 in forum Sea Doo How To & FAQs
    Replies: 226
    Last Post: 06-01-2015, 03:25 PM
  2. Questions About Metal Washer Upgrade
    By Flynfox in forum Sea Doo Open Discussion
    Replies: 16
    Last Post: 12-05-2006, 11:32 AM
  3. Installing Metal Washers Help
    By 1FastTrespiper in forum 4-Tec Performance
    Replies: 27
    Last Post: 08-29-2006, 10:47 AM
  4. Another "Where's the metal washers" thread
    By Big Red Monster in forum Sea Doo Open Discussion
    Replies: 0
    Last Post: 05-16-2006, 12:03 PM
  5. Metal Washers sneak peek
    By Green Hulk in forum 4-Tec Performance
    Replies: 19
    Last Post: 04-13-2006, 11:39 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules