Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20
  1. #11
    EVN81's Avatar
    Join Date
    Jul 2013
    Location
    Terschelling - the Netherlands
    Posts
    537
    +1
    45
    Quote Originally Posted by fartanas View Post
    Finally I figured out why the floating ring is not touching the carbon seal when I removed the jet pump. The impeller was unscrewed from the pump so it pushed the shaft forward.
    How long did you run the ski while leaking = impeller unscrewed ?
    Worst case scenario your thrust washers are shot and then you need to pull the engine or even replace.
    Check your oil filter for metal flakes.

  2. #12

    Join Date
    Aug 2013
    Location
    Vanuatu
    Posts
    26
    +1
    1
    By chance it happen when I was close to the shore, I came back at idle speed. I was pretty far away, alone and without any help one hour before. Threadings on the pump shaft are ok. I'm replacing the supercharger impeller, thrust washers are fine.
    I had a loose fixing mount that connect the pump to the plate, maybe the pump moved a little then the prop catched the wear ring then unscrewed or because the very rusty main shaft was stuck on the impeller (it helps to unscrew).

  3. #13
    EVN81's Avatar
    Join Date
    Jul 2013
    Location
    Terschelling - the Netherlands
    Posts
    537
    +1
    45
    Quote Originally Posted by fartanas View Post
    thrust washers are fine.
    You can't know for sure without opening the engine. But the least you can do is check your filter very good!
    Seen it happen before, same story as you and the engine was shot......
    Hopefully you have more luck

  4. #14

    Join Date
    Aug 2013
    Location
    Vanuatu
    Posts
    26
    +1
    1

    propeller / pump shaft o-ring size

    I've got it in my pump o-ring set 13$ for an o-ring...seriously!
    inside 28.3mm
    outside 31.86mm
    thickness 1.78mm
    shore 70 probably, cost is less than a dollar for one.

  5. #15
    Hey I have a 2010 rxtx that I want to do the drive shaft upgrade. Can anyone tell me pre post a link to a kit that has everything I need to do it ? Will this one work ?https://shop.pwcxtreme.com/WSM-SEADO...03-158-01K.htm

  6. #16

    Join Date
    Aug 2013
    Location
    Vanuatu
    Posts
    26
    +1
    1
    Don't forget to buy the rubber part that goes on top of the shaft, the tool for pushing the carbon seal and a new propeller o ring.

  7. #17
    That kit doesn’t have everything? What rubber part are you referring too?

  8. #18
    EVN81's Avatar
    Join Date
    Jul 2013
    Location
    Terschelling - the Netherlands
    Posts
    537
    +1
    45
    http://partsfinder.onlinemicrofiche....make=seadoopwc

    https://brpmanuals.com/seadoo-manual.htm

    Buy the 2011 manual, that one has the updated shaft with C-clip

    For only 19.50 it’s a pretty cheap investment/usefull tool

  9. #19
    I have the manual it just looked like that kit I linked had everything needed except the clamp for the pto

  10. #20
    ***double post***


Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Drive Shaft Bearing /Bellow and Carbon Seal Replacement
    By jvaski in forum 4-Tec Performance
    Replies: 4
    Last Post: 05-26-2017, 08:51 AM
  2. Replies: 8
    Last Post: 03-03-2017, 10:39 PM
  3. drive shaft removal ,carbon seal, etc questions
    By wazoo3 in forum 4-Tec Performance
    Replies: 8
    Last Post: 06-24-2011, 08:03 PM
  4. FS New Drive shaft tool, carbon ring and "C" clip
    By RXP-TOM in forum Sea Doo Classifieds
    Replies: 7
    Last Post: 10-12-2010, 09:39 PM
  5. Drive Shaft and help ?
    By WannabeGoing80 in forum 4-Tec Performance
    Replies: 0
    Last Post: 12-16-2006, 12:48 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •