Results 1 to 10 of 20
Thread: 2000 XLT1200 Part Out
-
07-30-2015, 05:51 PM #1
2000 XLT1200 Part Out
Parting out a 2000 Yamaha 1200XLT. I bought it for some parts and the trailer its on, so the rest needs to go. Cylinders, pistons, exhaust and head are gone already. Crank should be rebuilt, had aluminum from a melted piston go down the center hole. The rest is there and clean/working. I havent been able to check Hrs yet but id be very surprised if it was over 100, this is a clean ski. Hull has ownership.
Freshwater Ski!!!
Ill Start with some of the basics. All prices in USD. Willing to consider offers/package deals, dont be shy i dont bite or get upset with offers, i need it gone, you need it!
Start/Stop switch $45
Reverse lever/mechanism $30
Green hood w/ mirrors $60
Front and rear storage buckets $20 each
Ebox complete (Canadian version already setup for Dplate using stock sensor) $200
Seats (Pair, dark green almost black looking, no tears or marks that i can see) $100
Crank core $make offer
Crank cases (havent opened them but i believe clean) SOLD
Waterbox $40
Stock exhaust silencer system (WB to hull port) $35
Sponsons $20 (pair)
Trim handle $30
Trim cable $25
Reverse cable $30
Steering cable $50
Fuel tank $50
Oil tank $30
Oil pump $25
Triple 44 carbs $200
Reeds $60 for the set (havent checked them yet)
Pump complete just unbolted and disconected (includes shaft and nice prop) $300
Ride plate clean $50
motor mounts $40 (set of 4)
Hull $make me an offer (with paperwork)
Also have the starter, powervalve servo system, throttle cables, throttle, guage cluster, etc.
SOLD LIST:
Head
Cylinders and pistons
Exhaust from cylinders to waterbox
Cases
Hull Drains
reverse cable
trim system
steering nozzle
PM me if you dont see it listed here and need it like waterjackets, hull fittings, tow loop, rub rails etc.
If i sell it i will add it to a sold list.
CRJ
Also on x-h20.com
Last edited by CRJ; 08-11-2015 at 09:03 PM.
-
07-30-2015, 08:15 PM #2
-
07-30-2015, 08:17 PM #3
-
08-01-2015, 04:06 PM #4
-
08-01-2015, 08:24 PM #5
-
08-01-2015, 08:25 PM #6
-
08-01-2015, 08:26 PM #7
-
08-03-2015, 08:56 AM #8
-
08-03-2015, 04:56 PM #9
combo deal on the pump/shaft & midshaft unit?
I dont need the Wear ring housing or impeller, or the reverse bucket.
LMK
-
08-04-2015, 07:46 AM #10
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
FS 2000 GPR1200 part out with lots of aftermarket parts
By 111toybox in forum Yamaha ClassifiedsReplies: 29Last Post: 09-07-2013, 04:03 PM -
SOLD 951 947 CORE 2000 GTX Part out
By wkuadam07 in forum Sea Doo ClassifiedsReplies: 11Last Post: 08-19-2013, 06:24 AM -
FS - Parts 2000 Gtx part out
By ctct2118 in forum Sea Doo ClassifiedsReplies: 2Last Post: 02-14-2013, 01:10 AM -
FS 2000 GPR Part-Out
By rangermtb5 in forum Yamaha ClassifiedsReplies: 54Last Post: 12-28-2011, 02:34 PM -
FS 2000 GP1200R part out many after market parts
By 111toybox in forum Yamaha ClassifiedsReplies: 20Last Post: 09-28-2011, 08:10 AM
baffled here as well where to mount it other than the little hole on the...
NEW RIVA Yamaha 2012 & Newer 1.8L...