Results 1 to 9 of 9
  1. #1

    help with 15f grips?

    i want new grips, i would like to get odi grips, either rogue or ruffian....

    do i need 120mm or 130mm. its a 2015 15f. do i need to cut any of the handle bars off because i dont want to do that. or was that just on the older ones?????


  2. #2

    Join Date
    Mar 2013
    Location
    Logan Martin Lake, Alabama.
    Posts
    61
    +1
    3
    The ODI's will fit when you grind the flanges to the O.D. of the bar.

  3. #3
    DavidR's Avatar
    Join Date
    Jul 2013
    Location
    Forney,Tx
    Posts
    799
    +1
    45
    Cutting the end of the bar off isn't a big deal. Takes a few minutes with a hack saw. Just put 120mm ODI Rouges on mine last week.

  4. #4
    DavidR .....do u have pics?

  5. #5
    DavidR's Avatar
    Join Date
    Jul 2013
    Location
    Forney,Tx
    Posts
    799
    +1
    45

    help with 15f grips?

    The factory grips are molded onto the bar so they must be cut off. Then you cut as close to the washer as you can get to make sure you have enough bar for the lock rings to clamp onto.

  6. #6
    I do the same thing as davidr 120mm off amazon for 20 bucks!

    Only recommendation i would like to make is to buy the bmx donuts that go on the handle grips. My thumb rubs againsts the kill switch and always get cut and end up bleeding

  7. #7
    frankiexp's Avatar
    Join Date
    May 2016
    Location
    Inverness, FL
    Posts
    50
    +1
    2
    Are the grips sturdy as far as slippage? It's hard to beat the stock grips since they are molded on the bar with the bup on the end, but they are very uncomforatable! I have a set of odi rogue and am debating putting them on. Your input would help!

  8. #8

    Join Date
    Aug 2017
    Posts
    236
    +1
    19
    I did the ODI's on mine, but opted to get a slightly longer handlebar to accommodate 130mm grips. The 130's will fit the stock bar, but are too tight against the controls. Bought an anodized aluminum ATV bar and used the 130mm ODI's for a little bigger grip area.

    The ODI's grip the bar really tight and am confident they'll keep holding. Can always tighten them up, if needed.

  9. #9
    kawasakitim's Avatar
    Join Date
    May 2018
    Location
    Pembroke Pines, FL
    Posts
    20
    Great Tip, I cut off the ends in under 5 mins with a saws-all and bought these for $7 on Amazon and they match the color perfect!

    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	IMG_8905.jpg 
Views:	11 
Size:	40.2 KB 
ID:	433414   Click image for larger version. 

Name:	IMG_8904.jpg 
Views:	82 
Size:	66.3 KB 
ID:	433415   Click image for larger version. 

Name:	IMG_8903.jpg 
Views:	84 
Size:	71.2 KB 
ID:	433416  

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Help with Changing Prop on 15F
    By ercBOOSTED in forum Kawasaki PWC Performance (4-stroke)
    Replies: 13
    Last Post: 06-03-2013, 07:04 AM
  2. Needs help with kawasaki stx 15f power filter
    By centrino in forum Kawasaki PWC Performance (4-stroke)
    Replies: 1
    Last Post: 07-14-2011, 04:43 AM
  3. Help with 15F RPM kit performance
    By Super7Four in forum Kawasaki PWC Performance (4-stroke)
    Replies: 4
    Last Post: 07-01-2010, 12:38 AM
  4. Need Help With 08 15F SLO Mode...
    By tanglewood in forum Kawasaki Open Discussion
    Replies: 5
    Last Post: 04-28-2009, 02:48 PM
  5. Help with water pump stx 12/15f
    By Flytime in forum Kawasaki How To & FAQs
    Replies: 0
    Last Post: 06-07-2008, 02:36 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •