Results 1 to 7 of 7
Thread: 2004 eBay SC washers
-
06-06-2015, 11:18 AM #1
- Join Date
- Aug 2013
- Location
- Waterloo ON
- Posts
- 381
- +1
- 35
2004 eBay SC washers
Would you have any issue using these washers on an 04?
http://www.ebay.com/itm/111667483651?_trksid=p2055119.m1438.l2649&ssPageNa me=STRK%3AMEBIDX%3AIT
Seller says made by local machine shop of hardened steel and titanium coated..
-
06-06-2015, 12:00 PM #2
Washers are to critical of a part to just take a chance on some redneck making them out of his shop , my 2c would be to go on the GH store and get oem washers
-
+1 by:
-
06-06-2015, 01:57 PM #3
- Join Date
- Aug 2013
- Location
- Waterloo ON
- Posts
- 381
- +1
- 35
You can only buy OEM in the full kit.
-
06-06-2015, 04:17 PM #4
- Join Date
- Apr 2015
- Location
- Wales, UK
- Posts
- 1,550
- +1
- 106
RIVA http://www.4-tecperformance.com/inde...roducts_id=448
The $50 money back guarantee isn't much comfort when your looking at $2000+ of engine damage, and if your going for pulling the charger apart is saving $50 on washers worth it?
-
+1 by:
-
06-06-2015, 05:18 PM #5
There are only 2 kinds of washers I would EVER use,1 is OEM,2 is Riva......Other than that, save a couple of bucks now,and spend alot later....There is so much friction on those clutches you have no idea and to put some cheap, untested peices of metal in there because the seller says thier good???NO worth it....No different than a mail order bride,Selller says she good,till the 300lbs woman shows up to your door..
Also IF you still have a 2004 shaft in your ski,you should probably be thinking of a full rebuild ASAP anyway...Those bearings are WAY over due for replacement..Its not only the clutches that are prone to failure,BUT the bearings also..IF this were me,I would be rebuildign the whole charger with a completely new rebuild kit
-
+1 by:
-
06-07-2015, 12:49 PM #6
- Join Date
- Nov 2008
- Posts
- 75
- +1
- 6
This is the worst place to save money. Send the charger to Gerry and get a complete rebuild.
-
06-07-2015, 06:22 PM #7
- Join Date
- Aug 2013
- Location
- Waterloo ON
- Posts
- 381
- +1
- 35
I can rebuild the SC myself it's not that hard. I will likely do the full OEM kit after reading these posts, and then sell the machine in the fall
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
2004 SC washer part numbers
By bluestram in forum 4-Tec PerformanceReplies: 4Last Post: 04-04-2015, 08:06 AM -
2004 GTX SC pulled. Have a question on the Washers.
By Noyama in forum Sea Doo Open DiscussionReplies: 8Last Post: 04-28-2013, 06:45 PM -
Ebay SC washers
By 05Limited in forum 4-Tec PerformanceReplies: 15Last Post: 06-27-2008, 11:48 AM -
SC washers on Ebay
By NCHeel in forum Sea Doo Open DiscussionReplies: 12Last Post: 09-22-2006, 12:14 AM -
2004 GTX SC with plastic pump?
By Green Hulk in forum 4-Tec PerformanceReplies: 17Last Post: 08-15-2005, 09:26 PM
So far no answer on cause, pressure testing intercooler today. The K team...
2022 Ultra 310X problems.. water...