Results 1 to 10 of 18
-
12-05-2005, 09:57 PM #1
Took some pics while pulling off pump
I took some pics for my file while I was removing the pump for the soon to be mods, and here`s what I found:
...only 26 hrs. this time around...PR...
Last edited by Pale Rider; 02-25-2007 at 12:06 PM.
-
12-05-2005, 10:45 PM #2
do u actually need to support the drive shaft when the pump is out
i hope not
lol
PR... time for a SOLAS
-
12-05-2005, 11:06 PM #3
I never support my driveshaft while my pump is out.
-
12-05-2005, 11:52 PM #4
yea me neither.... the thru-hull seal and accordian boot should support it enough. I've left mine dangling for days or even week or two at a time... never had a problem yet.
-
12-06-2005, 10:52 AM #5
I don't know why but I just got in the habit of supporting the shaft from the first time I took my pump off. Now it is just second nature to support it whether it needs it or not.
-
12-06-2005, 05:55 PM #6
It does hang down quite a bit, and you can move it around, which I don`t really know if that is good for it, but one thing is that sucker should slide right back in without sticking my hand in there. I didn`t think it was a good idea to stress whatever is on the other side, carbon seal/ring, accord boot etc., anyways it can`t hurt being supported!...PR...
-
12-06-2005, 06:07 PM #7
Hey PR, did you ever try the freezer trick for wear ring removal / replacement? Works very well and no danger of damaging the pump.
-
12-06-2005, 06:18 PM #8
I wanted to try the "Shibbzero" method, but I saw all this glue spooging out around the wear ring, and decided to cut it. I didn`t think the first people to RR wear ring cut to deep, but at least it`s not dammaged to where I can not install the SS wear ring...PR...
-
12-06-2005, 06:49 PM #9
"Shibzero method"- too funny! I don't know if it works with the SS ring, but the plastic ring just drops right in using that trick. Vic
-
12-06-2005, 06:59 PM #10
Putting pump in freezer don't work with aluminum wear ring I had made,had to cut it out.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Took some pics of pistons sending head to jim
By Tanny in forum Yamaha PWC Performance (2-stroke)Replies: 11Last Post: 01-26-2008, 10:01 AM -
Filled my ridplate holes today. Took some pics.
By mksmi in forum 4-Tec PerformanceReplies: 24Last Post: 12-27-2007, 02:14 PM -
Took Some Pics of the Beach Last weekend.
By ADAMBOMB in forum Open DiscussionReplies: 6Last Post: 01-17-2007, 11:08 AM -
Went riding today....took some pics
By TorquePhoto in forum Sea Doo Open DiscussionReplies: 17Last Post: 10-25-2006, 02:57 AM -
Removed SC, took some pics...
By Pale Rider in forum 4-Tec PerformanceReplies: 32Last Post: 12-20-2005, 08:01 PM
So I found a Bosch 0280750009and threw it on the ski. I needed 4 6mmx45mm...
2018 RXTX300 Cutting out under...