Results 1 to 10 of 30
Thread: My new RXX hood came in today
-
10-25-2005, 03:32 PM #1
My new RXX hood came in today
I just preassembled everything and put it on the scale. It only weighs 9.5 lbs
The top storage bucket and side trim pieces only add 2 more pounds.
If my wife leaves me alone i should have it all bolted up on the ski tonight.
Can't wait to weigh the RXP hood and trim pieces to see how much weight im saving.
-
10-25-2005, 03:38 PM #2
Jerry Make Sure to put the harness in before you put it on the boat.
It sucks doing it afterwards.
I was able to loosen a few of the screws and get it through but it would have been lots easier before I mounted it.
David
-
10-25-2005, 03:46 PM #3
aaaaah! thanks for the tip. Anything else you can think of?
-
10-25-2005, 07:02 PM #4
Take off the chrome pieces and drill out the rivits from the front.
Wedge a 2x4 under the hood bracket to hold it compressed some it makes it easier to put back togather.
You can get the stock hood off without messing with that bracket at all.
Mount the temp sensor before install as well. I put mine right under the gauges to get good air flow to make sure and get a true reading.
-
10-25-2005, 08:22 PM #5
Its installed!!!
I even came up with a crafty little place to put my boost and oil pressure gauge's.
How do you guy's like the trick location of the billet UMI gas cap?
Not to sure about it yet, but it's growing on me.
-
10-25-2005, 08:28 PM #6
jerry that is awesome looking.....man how long did that take you....didn't you just get that hood?......how much did that cost too cuz thats something i wanna do!
-
10-25-2005, 08:32 PM #7
it only took me a couple of hours.
cost using new parts was nearly $500
-
10-25-2005, 08:38 PM #8
That is the same place I moved my gas caps too.
-
10-25-2005, 08:41 PM #9
No kidding? Cool! How do you like them there?
I figured if i was going to have a high dollar billet gas cap it should be seen
-
10-25-2005, 08:42 PM #10
- Join Date
- Jun 2005
- Location
- Cayman Islands
- Posts
- 705
Looks great bro, when you get a chance email me the parts list, I want an RXXP too
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
VF3's came in today....
By OBXJeepGuy in forum Yamaha PWC Performance (2-stroke)Replies: 49Last Post: 11-20-2008, 07:50 PM -
First peek at my new RXP hood design
By inteljd in forum Sea Doo Open DiscussionReplies: 5Last Post: 05-03-2008, 08:55 PM -
Well boys my R&D pully kit came in today.
By TOQUICK250X in forum Kawasaki PWC Performance (4-stroke)Replies: 4Last Post: 11-27-2007, 11:39 PM -
got my new Rude Performance controler in!
By beachboy66 in forum 4-Tec PerformanceReplies: 6Last Post: 08-16-2006, 09:15 PM -
My engine came in today *pics*
By Green Hulk in forum 4-Tec PerformanceReplies: 47Last Post: 04-14-2006, 10:49 PM
rxp 2019 14hrs, with supertech valves, supertech springs, supertech...
SuperTech Lightweight Valves /...