Results 1 to 10 of 49
Thread: RXP twin pipe system
-
10-13-2005, 02:32 PM #1
- Join Date
- Sep 2005
- Location
- Sittingbourne United Kingdon
- Posts
- 753
- +1
- 1
RXP twin pipe system
Today finally getting over my cold.Went to the garage looked at my beast. said to myself time to start the mod so out with the ruler marked up the holes drilled to holes one either side at the back fitted two GTX 97 exhaust billets looking good at mo waiting on stainless steel T peice and water fittings to finish the job
-
10-16-2005, 09:52 PM #2David
- Join Date
- Jun 2005
- Location
- Southaven, MS
- Posts
- 1,956
- +1
- 1
Post pics
-
10-17-2005, 12:44 PM #3
- Join Date
- Aug 2005
- Location
- Kenner, LA
- Posts
- 4,824
- +1
- 50
Thats what I wanted to do also! My shop is gone from Hatrina. Damn, wanted to be the first out the gate with this. Can`t use my bender without 220. Good luck.
-
10-18-2005, 03:40 AM #4
- Join Date
- Sep 2005
- Location
- Sittingbourne United Kingdon
- Posts
- 753
- +1
- 1
Wil try and post pic s When finished at mo still waiting a delivery
-
10-21-2005, 04:50 PM #5
- Join Date
- Sep 2005
- Location
- Sittingbourne United Kingdon
- Posts
- 753
- +1
- 1
well today more or less finished the twin pipe mod just waiting for block off plate for the orginal exhast hole. fired her up and sounds brill cant wait to get it in the water..
-
10-21-2005, 05:43 PM #6
- Join Date
- Aug 2005
- Location
- Kenner, LA
- Posts
- 4,824
- +1
- 50
Post pics bro! Where are you getting block off plate? Fabbing it yourself. Do you feel there will be issues from WOT to off throttle backwash or assending after a jump? Bells incorporated?
-
10-21-2005, 05:58 PM #7fabrication guru
- Join Date
- May 2005
- Location
- Lake Travis austin, TX
- Posts
- 1,157
- +1
- 2
other then a cool sound i don't see much of a performance gain from duel outlets after the stock waterbox.
let us know if there was any improvements.b im sure it looks cool anyway 
hoss
ive got the rear exit exhuast on my boat and havn't had any issues with jumping or slowing down quickly. it curves up about 6 inches in so theres not really to far that the water can back up in there. looks and sounds way better.
-
10-22-2005, 04:10 AM #8
- Join Date
- Sep 2005
- Location
- Sittingbourne United Kingdon
- Posts
- 753
- +1
- 1
Ive used all seadoo parts + two rivirracing parts ie the Straight thro pipes. Just cut the main rubber hose for the angles i needed a had a stainless T piece made. Walting for 6mm ali plate to make block off plate
-
10-22-2005, 05:50 AM #9
- Join Date
- Aug 2005
- Location
- Kenner, LA
- Posts
- 4,824
- +1
- 50
Please keep us updated on this.
-
10-22-2005, 08:02 AM #10
- Join Date
- Sep 2005
- Location
- Sittingbourne United Kingdon
- Posts
- 753
- +1
- 1
Pics
Reply With QuoteThread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
FS RXX Twin Pipes & Some RXP/RX goodies
By Racr314 in forum Sea Doo ClassifiedsReplies: 14Last Post: 08-17-2011, 03:50 PM -
800CC Twin Piped SLTX
By ph2ocraft in forum Polaris Open DiscussionReplies: 9Last Post: 05-20-2008, 04:25 PM -
Twin piped 951 X4
By Gregscalade in forum Conversion PWC Performance SkisReplies: 29Last Post: 08-11-2007, 11:12 AM -
Twin Pipes
By CrazyA in forum 2-Stroke PerformanceReplies: 9Last Post: 04-25-2007, 09:54 AM -
Twin Piped Virage
By TxVirageTx in forum Polaris PWC PerformanceReplies: 11Last Post: 12-20-2006, 10:18 PM
Seadoo used to use a grease-able needle bearing for the drive shaft seal...
2021 Sea Doo GTX300 Limited - How...