Results 1 to 10 of 14
Thread: Pitch of a stock RXP impeller
-
10-04-2005, 08:01 PM #1
Pitch of a stock RXP impeller
When I convert my GTX SC with the RXT driveshaft, wear ring, and impeller, I was wondering what is the pitch of a stock RXP impeller and where would I want to be if I decide to purchase a Solas?
-
10-04-2005, 08:08 PM #2
pitch
I think stock RXP is 13/18 if i'm not mistaken.
-
10-04-2005, 08:32 PM #3
ebay
Just found this on ebay posted by Rivamotorsports:
"You are bidding on a new stock (original) impeller from a 2005 SeaDoo RXP watercraft. The impeller was installed in a new craft by the manufacturer and then removed prior to the craft ever hitting the water. It was replaced with an aftermarket racing impeller at the request of our customer. It is in new condition except for the typical indications of installation and removal. Manufacturers part# 267000096. New replacement value is $287.89. We are also including the rubber impeller boot shown in the picture, a $10 additional value. According to the Sea-Doo technical reference manual, this impeller is a variable pitch 10-21 degree. The outside diameter is 155.5mm / 6.12in."
10-21??? Stock can that be right, then they suggest 13/18 for stock application replacement. Wonder if this would hurt acceleration.
-
10-04-2005, 08:37 PM #4
With the mods you have I`d be looking at a 14/19 solas.
-
10-04-2005, 09:37 PM #5
I would talk to dave at impros.com. Then order a used one off ebay and have him pitch/polish it.
-
10-04-2005, 09:55 PM #6
Re: ebay
Originally Posted by meeper
-
10-05-2005, 07:24 AM #7
EBAY
I got no idea, dont know much about them either, trailing edge, leading edge, what are they??
-
10-05-2005, 07:51 AM #8
different companies make different impellers... if you go to skat trak and look at their RXP stock replacement impeller-- it is a: 4-Blade 10/21 159-83-28 Swirl.... solas stock replacement may be 13/18..
-
10-05-2005, 09:55 AM #9
Originally Posted by VFX_Artist
Thanks, appreciate the good info..
-
10-06-2005, 05:46 AM #10
What are you waiting until winter to install the driveshaft setup Jay...lol.. I thaught you would have it by now....
Just be ready to do some prop re-pitching...It might take a while to figure out your best application...
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
What's the pitch of a stock spark impeller?
By SunSeaDoo in forum Sea Doo SparkReplies: 5Last Post: 05-02-2016, 01:26 PM -
Anyone have pics of a stock RXP-X engine comparment?
By Jarrett in forum 4-Tec PerformanceReplies: 5Last Post: 08-07-2009, 11:08 PM -
Topspeed of a Stock RXP in 1-1.5ft chop?
By crxski in forum 4-Tec PerformanceReplies: 12Last Post: 06-15-2009, 12:54 PM -
Pic of Stock RXP Impeller
By Red Devil in forum 4-Tec PerformanceReplies: 4Last Post: 10-10-2005, 02:42 PM -
Stock RXP degree impeller?
By meeper in forum 4-Tec PerformanceReplies: 9Last Post: 09-18-2005, 08:11 PM
well it sounds like I know what my next step is then
1996 gsx cavitation