Results 1 to 10 of 13
-
04-05-2011, 02:45 PM #1
- Join Date
- Dec 2009
- Location
- Meddle East
- Posts
- 66
Engine Tempruter Alarm / Need Help
Hello,
I'm just facing problem on Engine tempruter alarm this come after 10 mins when I started the jetski!!! I'm just installed Intake great,Intake manufolt,ride plate,Riva intercooler,air power filter & engine intercooler kit. I believe I should be on safe side but I don't know how's this alarm came!!! Please any could tell me how to solve or any facing this problem !!??
-
04-05-2011, 02:49 PM #2
did you replace the strainer? if you did make sure that you have the hole in the right direction.
-
04-05-2011, 02:53 PM #3
- Join Date
- Jul 2008
- Location
- Wylie, Texas
- Posts
- 3,576
- +1
- 1
Verify your pissers are putting water out on both sides. When I had something like this happen I had a kinked water hose.
-
04-06-2011, 12:37 AM #4
- Join Date
- Dec 2009
- Location
- Meddle East
- Posts
- 66
-
04-06-2011, 12:45 AM #5
It's the piece from the Riva intercooler kit that goes in the pump. It has a hole in one side that needs to face towards the front of the ski.
This is the part:
http://www.4-tecperformance.com/inde...oducts_id=1399
-
04-06-2011, 11:14 AM #6
What he just said. There is a hole on one side of the strainer and a hole in the pump. Make sure these holes match up your you will not get water to your engine and it will over heat and melt all the plastic resonators in the exhaust......ask me how i know...
-
04-06-2011, 02:47 PM #7
Is it when you are flushing the Ali or in the water. If it when you flushing the ski it's definitely because water flows backward through pump and not to the engine. If it's in the water then it's definitely the pump strainer installed backwards or a cooling lime came of.
-
07-02-2011, 04:34 AM #8
hello
please help sombody.
this ski is a fzr 09
whit this mod
r&d engine/intercooler cooling kit
r&d air filter kit
r&d surge protector kit
r&d r2 ecu
r&d suppression removal kit
r&d intake manifold kit
r&d monster c1 weel
r&d intercooler kit
and im put a windeband lamda gauge kit on it "inovate"
and im take the 12v + to a rel from this wire.
http://www.greenhulk.net/forums/show...=install+gauge
I put the ski into the water and warm her up 2-3min on idle.
But when I start to accelerate a little more than over 3,000 + +, so then the engine go in a safe mod and the almar start to sound and on the display engine lamp flashes.
And now im wonder what the crap did im wronk on this 1?
Thank you
Thomas Wester
-
07-02-2011, 05:03 AM #9
- Join Date
- Jan 2008
- Location
- Currituck, North Carolina, United States
- Posts
- 4,994
- +1
- 290
-
07-02-2011, 06:57 AM #10
hello
i have check all plugs now and nothing..
any other idea??
Thank you.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Engine OverHeat Alarm, Please Help !!
By Jayson005 in forum Polaris PWC PerformanceReplies: 2Last Post: 06-22-2010, 11:23 PM -
Difficult time balancing out engine temp. I need help.
By xplayer2885 in forum Polaris Open DiscussionReplies: 21Last Post: 09-03-2009, 04:01 PM -
Installing RXP engine, had accident need help?
By lawracing in forum Conversion PWC Performance SkisReplies: 51Last Post: 02-18-2009, 02:34 AM -
Engine moving around - need help!!!
By reustic in forum Polaris Open DiscussionReplies: 7Last Post: 07-03-2008, 12:28 PM -
ultra 150 engine vibratin alot need help!
By jramos in forum Kawasaki How To & FAQsReplies: 8Last Post: 01-25-2008, 01:29 PM
I loosened the ride plate bolts and it made enough clearance to slide out...
FX HO Impeller Project &...