2011 rxp x

[supra_power2]

got a 2011 rxp x on the way, i did some searching but cant find what im looking for

im wonder what my speed should be once its broke in with the following mods.. . . .

stock charger/ stock injectors/stock ecu/ stock valves/internals

engine
riva sd rear hull exit exhaust
riva pro series intake

handling
opas block off kit
riva ride plate
ride plate holes filled
either top loader grate or r&d grate??
riva pump wedge 2degree with exttension rod
solas impeller not sure yet in size?
riva changable nozzle rings


190lb rider, 50-78 degree water 1500ft sea level

what should i expect and any other suggestions? i am hoping for 75-77 mph

[mrbtd]

ur not getting to 75 without an upgrade in the air intake. The fizzle 4" air kit is going to be the best bang fo rthe buck.

Dont waste your $$ on nozzle and rings just find an RXP 83mm nozzle.

[boBO]

Go with R&D grate not Riva
DONT USE RIVA ride plate ( you need allot of prussure works )

[Rutcutter]

Your gonna need the Riva Speed Module overide before your gonna go over 68mph.

[troyheb]

ur not getting to 75 without an upgrade in the air intake. The fizzle 4" air kit is going to be the best bang fo rthe buck.

Dont waste your $$ on nozzle and rings just find an RXP 83mm nozzle.

He shows the Riva pro series intake, better than a Fizzle.

+1 on the 83mm nozzle.

[troyheb]

Go with R&D grate not Riva
DONT USE RIVA ride plate ( you need allot of prussure works )

+1 R&D grate
+1 Riva plate lots more work than just bolting it on.

[troyheb]

Your gonna need the Riva Speed Module overide before your gonna go over 68mph.

Hes got a RXPX.

[troyheb]

got a 2011 rxp x on the way, i did some searching but cant find what im looking for

im wonder what my speed should be once its broke in with the following mods.. . . .

stock charger/ stock injectors/stock ecu/ stock valves/internals

engine
riva sd rear hull exit exhaust
riva pro series intake

handling
opas block off kit
riva ride plate
ride plate holes filled
either top loader grate or r&d grate??
riva pump wedge 2degree with exttension rod
solas impeller not sure yet in size?
riva changable nozzle rings


190lb rider, 50-78 degree water 1500ft sea level

what should i expect and any other suggestions? i am hoping for 75-77 mph

Run a 15/22. You should be 75+ Also pull the flame arrestor out of your intake manifold

[supra_power2]

thanks troyheb, ok so let me get this straight, ( and yes its a RXP X 255 . . . . .not rxp

leave stock ride plate or what??
go with R&D grate??
will the pro series (under seat ) intake be good or do i need a 4" air duct type one?? reason i choose the pro sieries is i like the way it sounds
and whats this about a speed module ?? never heard of it
and use a 83 mm nozzle?
and 15/22 solas

should be 75 ish?

[troyheb]

thanks troyheb, ok so let me get this straight, ( and yes its a RXP X 255 . . . . .not rxp

leave stock ride plate or what??
go with R&D grate??
will the pro series (under seat ) intake be good or do i need a 4" air duct type one?? reason i choose the pro sieries is i like the way it sounds
and whats this about a speed module ?? never heard of it
and use a 83 mm nozzle?
and 15/22 solas



should be 75 ish?

yes, and fill your ride plate holes
yes
yes it will be good
your ski do not need the speed module
yes
yes
I was 76, 77 with basically the same mods.