Search

Page 1 of 5 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    6
    Views
    150

    They look perfect. They only have 10 hours on...

    They look perfect. They only have 10 hours on them. And the strap is not white.
  2. Might have to clean the new injectors due to crap...

    Might have to clean the new injectors due to crap in the fuel filter
  3. likely injectors are clogged, and the fuel filter...

    likely injectors are clogged, and the fuel filter too..esp if the gas was gummy

    plenty of info here on dealing with those issues

    how many hours?

    and welcome aboard GH!
  4. Replies
    10
    Views
    440

    Cam timing is very important, but a simple check...

    Cam timing is very important, but a simple check would be to install new plugs no matter what they look like, I’ve seen new looking plugs be fouled and cause rough idle
  5. Replies
    37
    Views
    1,093

    the startup and idle sounds just dandy to me! ...

    the startup and idle sounds just dandy to me!

    and best of all no maint lamp flashing!
  6. Replies
    24
    Views
    1,022

    Really ??? Its a filter that you can clean...You...

    Really ??? Its a filter that you can clean...You cant clean a Yamaha fuel filter. Been working on skis for close to 30 years & have yet to come across a better fuel filter. Heck Seadoo stole the...
  7. Replies
    5
    Views
    181

    I believe they recommend plugs every 100 hours. ...

    I believe they recommend plugs every 100 hours. With that said, I put new ones in when I winterize. I don’t worry about the fogging oil.
  8. Replies
    10
    Views
    558

    There is a foam seal or just run a ring of clear...

    There is a foam seal or just run a ring of clear silicone where the wear ring seals against plate,install pump let sit for 24 hours to cure.
  9. Replies
    6
    Views
    214

    First thing would be to check for a collapsed oil...

    First thing would be to check for a collapsed oil filter.
    Do the Easy stuff first.
  10. Replies
    5
    Views
    244

    You cant run a 3D without a pump. The loud...

    You cant run a 3D without a pump.

    The loud "whooping" noise is the driveshaft smacking the pump support because there is no support when the pump is out.

    You need to remove the clip for the...
  11. Replies
    10
    Views
    574

    I do carb rebuilding at a very reasonable price &...

    I do carb rebuilding at a very reasonable price & only use genuine Mikuni kits. PM me if interested.
  12. Replies
    27
    Views
    1,314

    I would think if you take the plug out of the...

    I would think if you take the plug out of the flywheel cover and turn the engine a bit you should be able to tell if there's fuel in there. If there's only a bit I would think the flywheel would be...
  13. Replies
    1
    Views
    281

    It could be lean because of an air leak. Is the...

    It could be lean because of an air leak. Is the rear crank seal new? Was the engine pressure tested?
  14. Replies
    15
    Views
    1,006

    no..... replace the pump bearings and shaft with...

    no..... replace the pump bearings and shaft with the updated items from the 300/310 models.
  15. I'd say a 15f

    I'd say a 15f
  16. Replies
    8
    Views
    577

    Double check his work. Try a couple of drops of...

    Double check his work. Try a couple of drops of gas straight down the carb to see if it fires on that. If so, fuel delivery issue. If he didn't clear all passages in the carb (There are 3 very...
  17. Replies
    4
    Views
    390

    solid tops are better. But as stated, screw tops...

    solid tops are better. But as stated, screw tops will work as well.
  18. Replies
    4
    Views
    390

    yep, just tighten down the screw tops with some...

    yep, just tighten down the screw tops with some pliers.
  19. Replies
    4
    Views
    390

    if both are BR8ES then the top doesn't matter. if...

    if both are BR8ES then the top doesn't matter. if you get the screw ones just take some pliers and make sure its tightly screwed on. I have had one over many many years come unscrewed and caused...
  20. There are many gps apps for your phone that work...

    There are many gps apps for your phone that work great.
  21. Replies
    3
    Views
    271

    Make sure this bracket is off the exhaust and not...

    Make sure this bracket is off the exhaust and not on the cylinder either. then its a PIA bottom end in first turn and twist top. Maybe a couple of F%3ks inbetween
  22. Sorry, my bad, I wasn't paying attention. You...

    Sorry, my bad, I wasn't paying attention. You have the 65u engine. Not much really, they are proven reliable when cared for. I think there is a rejet suggestion somewhere, and a balancing mod that...
  23. Replies
    6
    Views
    368

    I have seen a couple of instances where the ring...

    I have seen a couple of instances where the ring gear has broken off the flywheel on the 701/760's. Not common, but it does happen
  24. Also the Igniter is buzzing when power is turn...

    Also the Igniter is buzzing when power is turn on. Probably not normal.
  25. Replies
    3
    Views
    354

    Just change the filter. Your fine. I make it a...

    Just change the filter. Your fine. I make it a habit to change plugs and filters and oil after every season. Some times twice depending on hours and riding style
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4