Search

Type: Posts; User: psycho rxp

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    14
    Views
    519

    FS - Parts :roll:=D>

    :roll:=D>
  2. Replies
    14
    Views
    519

    FS - Parts I knew it was the perfect fit for him ;)

    I knew it was the perfect fit for him ;)
  3. Replies
    14
    Views
    519

    FS - Parts Do it Gus ;)

    Do it Gus ;)
  4. It had to of run hot enough to melt the exhaust...

    It had to of run hot enough to melt the exhaust temp sensor previously. The alarm should’ve been going off for quite some time before it actually melted out & quit working. Check for restrictions or...
  5. Replies
    4
    Views
    169

    Also double check the nosecone on the prop didn’t...

    Also double check the nosecone on the prop didn’t come loose & walk up the shaft
  6. The stock pistons are good to a point, but for...

    The stock pistons are good to a point, but for high rpm high boost applications, I usually open the bore to give .005 piston to wall clearance. Stock piston Clarence is pretty tight.
  7. Replies
    2,089
    Views
    230,458

    When it loses fuel pressure does the voltage drop...

    When it loses fuel pressure does the voltage drop to the pump? It could be a wiring issue, or even an ECU issue if so.
  8. Replies
    8
    Views
    184

    Whatever you get make sure I can handle 58 psi or...

    Whatever you get make sure I can handle 58 psi or more of fuel pressure. No plastic filters
  9. Replies
    14
    Views
    453

    The new 19s don’t require rebuilds, they are...

    The new 19s don’t require rebuilds, they are supposed to be checked at 200 hours on the 300’s
  10. Check your coil packs for cracks,Or swap with a...

    Check your coil packs for cracks,Or swap with a known good ones. they don’t last forever
  11. Need to stick with OEM rebuild kits, for...

    Need to stick with OEM rebuild kits, for durability if you want it to last.
  12. Welcome to the forum. You might get more help...

    Welcome to the forum.
    You might get more help Starting a new thread in the 4 tec performance area.

    First I would check the boost hoses, at the intercooler and supercharger for a loose clamp,...
  13. Replies
    3
    Views
    135

    Check to see if the intercooler is plugged up

    Check to see if the intercooler is plugged up
  14. Replies
    4
    Views
    183

    Yes, I use it on my 19’ RXT-X300 , works great &...

    Yes, I use it on my 19’ RXT-X300 , works great & even smells good too;)
  15. Replies
    34
    Views
    1,177

    The dash pac is not 100% operational on the new...

    The dash pac is not 100% operational on the new dash, that comes with the 19’s yet.
  16. Replies
    6
    Views
    219

    View Post

    Where is your oil level at? Itís supposed to be in the middle of the two bends on the dipstick. If itís overfilled above the top then any it will blow out the tops valve hose. With an aftermarket air...
  17. If you have a trailer you could just leave the...

    If you have a trailer you could just leave the trailer tipped back & prop it up maybe ...
  18. Replies
    5
    Views
    226

    You will have to manually tune the idle map,...

    You will have to manually tune the idle map, specifically where the start up cells are located while cranking. Start by removing 15% where the cells light up while cranking. It may take a few tries...
  19. Replies
    4
    Views
    172

    Try adding a 2 mm spacer to the cone, and see if...

    Try adding a 2 mm spacer to the cone, and see if it keeps The max RPM down
  20. Replies
    18
    Views
    1,271

    Check for a leak from your PTO bearing boot,...

    Check for a leak from your PTO bearing boot, where the driveshaft goes into the back of the motor. Best bet is to clean the hull, and put a white rag underneath that area. Doesnít even need to be...
  21. Double check the fuse for coil number 2, make...

    Double check the fuse for coil number 2, make sure the pins are supplying power to the fuse and across it. If you don’t have access to another harness for the engine you can use, might try cutting...
  22. I have a Riva stage 2 + IMUK 8550 flash. With...

    I have a Riva stage 2 + IMUK 8550 flash. With low fuel and trimmed all the way up, I get 77 to 78 on the dash with a stock Depitched prop.
  23. Could still have a bad engine harness with...

    Could still have a bad engine harness with continuity. If only one or 2 strands of wire are still connected.
    Or a bad ECU coil driver.
  24. A) The seal is getting too hot, from lack of...

    A) The seal is getting too hot, from lack of oil. “Oil sprayer jet clogged?
    B) Improper assembly/defective oil seal in number 2
  25. The replacement is now failing two hours later?...

    The replacement is now failing two hours later? Was it rebuilt?

    Either way looks like the seal is defective behind the impeller.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4