Search

Type: Posts; User: psycho rxp

Page 1 of 8 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    15
    Views
    1,233

    The magnet is not gonna get a stainless steel...

    The magnet is not gonna get a stainless steel bolt, Look for it back by the drain plugs, it may show up eventually
  2. Replies
    7
    Views
    601

    I saw the same dude on Facebook. I guess it all...

    I saw the same dude on Facebook. I guess it all depends on how much heat they can withstand, When out of water , running on the hose.
    I Would need to see some test results posted ,before I would...
  3. Replies
    36
    Views
    3,963

    Same here ;) Went six weeks without it

    Same here ;) Went six weeks without it
  4. Replies
    36
    Views
    3,963

    Well, I just got mine back out of the shop about...

    Well, I just got mine back out of the shop about a week-1/2 ago & running good so far. They replaced my engine under warranty. I put about six hours of break-in on the new motor,so far so good....
  5. Replies
    3
    Views
    377

    Thanks guys, I’m guessing when they put the new...

    Thanks guys, I’m guessing when they put the new motor in, they changed the engine serial number or something in the ECU ,and it doesn’t match now. The paperwork doesn’t show a new ECU and the hours...
  6. Replies
    3
    Views
    377

    Maptuner X error 301 ?

    Has anyone had error code 301 come up (programming error) ?
    Does anyone know what it means?
    Also, It Just had a new engine put in it ��

    455662
    455663
  7. Replies
    12
    Views
    571

    Those were the poor quality stainless bolts that...

    Those were the poor quality stainless bolts that they used in 04-05. The 06+ bolt you have pictured next to it, is the upgraded one.
  8. Replies
    12
    Views
    571

    The supercharger should not spin freely, it’s...

    The supercharger should not spin freely, it’s gear driven off the fly wheel. The clutches could have let loose in the supercharger, or the fly wheel bolts sheared off. Either way the PTO cover needs...
  9. Replies
    8
    Views
    867

    Remove the spark plugs and spin it over see if...

    Remove the spark plugs and spin it over see if any of it comes out
  10. Replies
    24
    Views
    3,117

    I’d Keep the RXT Hull, as the RXP is only good...

    I’d Keep the RXT Hull, as the RXP is only good for flat water SPEED #’s . I’ve had both.
  11. Replies
    25
    Views
    1,164

    You will need aftermarket, or lightened intake...

    You will need aftermarket, or lightened intake valves, retainers, and should go open loop cooling @ 8800 RPM +

    Also look into getting pressure reliefs installed in the pump tunnel, to keep the...
  12. I would look into your DESS post first, They can...

    I would look into your DESS post first, They can go bad.
  13. Replies
    47
    Views
    1,936

    View Post

    Isnít there a check valve built into the fuel pump itself, On the pressure side?
    Did you install the relay for the Riva fuel pump?


    Iíve had one go bad before and had similar issues. The rough...
  14. Replies
    8
    Views
    291

    Just an FYI, the “E” temp is not exhaust...

    Just an FYI, the “E” temp is not exhaust temperature, “E”stands for earth temp( outside air temp)
  15. Replies
    36
    Views
    3,963

    In my case, it’s not the same cylinder , it was...

    In my case, it’s not the same cylinder , it was the middle cylinder with the issue. It is currently at the dealer, still waiting to be taken apart and diagnosed. I think the problem is most are still...
  16. Remove the glove box, and go through the top

    Remove the glove box, and go through the top
  17. Replies
    3
    Views
    254

    The 300 kit comes with the guide for the holesaw...

    The 300 kit comes with the guide for the holesaw to cut the manifold in the proper place.
  18. Replies
    37
    Views
    2,638

    19’

    19’
  19. Replies
    37
    Views
    2,638

    Yup, 42 hrs on the clock, middle cyl, flatwater...

    Yup, 42 hrs on the clock, middle cyl, flatwater River cruising at 7700 rpm when it stalled and wouldn’t restart. Let it sit a few minutes, then tried again, and the motor locked up:evil:
  20. Should have no worries on the valves, those were...

    Should have no worries on the valves, those were the 04-05 year motors , with the sodium filled exhaust valves. .
  21. Replies
    37
    Views
    2,638

    Me too. Let’s just hope the new motor will have...

    Me too.
    Let’s just hope the new motor will have some sort of upgraded valves, or I fear, this could happen again. If nothings changed on the new motor, I may be buying a set of valves to put in...
  22. Replies
    37
    Views
    2,638

    Mine dropped the middle cylinder valve, Will know...

    Mine dropped the middle cylinder valve, Will know more hopefully later this week when they pull the head, to see if it’s isolated to the intake valves, or something else :roll:
  23. Replies
    28
    Views
    1,293

    The supercharger slip could also be low, causing...

    The supercharger slip could also be low, causing it to not build full boost. Might want to check into that. They can loose some tension after they break in after the rebuild. Do you know if OEM...
  24. Can-doo Pro or Dealer only. The 05’ RXT did...

    Can-doo Pro or Dealer only.


    The 05’ RXT did not have VTS
  25. I assume you already checked all the fuses , and...

    I assume you already checked all the fuses , and changed spark plugs already?

    Have you tried a different set of known good coils yet?

    What does your compression #’s look like?

    Did you just...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4