Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Those SLT's came with aluminum 5 vane pump...

    Those SLT's came with aluminum 5 vane pump stators that chip/crack pretty easy. Missing vanes will hurt accel. The stainless 6 vane will fit.
    Pretty sure stock impeller was a 4 blade, to me it felt...
  2. Replies
    10
    Views
    215

    Good to hear. hmmm... Check/reinforce the seat...

    Good to hear.

    hmmm... Check/reinforce the seat latch. The plastic seats crack- there should be a thread on here somewhere.
  3. Replies
    21
    Views
    358

    The "update stator" is a direct replacement for...

    The "update stator" is a direct replacement for the original.Bolts right in with no modification.
    Original is gen1, update is gen3. There is a slight difference in the way they look .
  4. Replies
    7
    Views
    150

    Welcome to GreenHulk .

    Welcome to GreenHulk .
  5. Replies
    10
    Views
    215

    The last sentence, I meant that taking the 4 long...

    The last sentence, I meant that taking the 4 long bolts loose to remove the drive shaft and grease splines will keep the bolts from corroding into the pump base. Some people have had the bolts break...
  6. Replies
    10
    Views
    215

    Lucky it didn't melt the exhaust hose, watch for...

    Lucky it didn't melt the exhaust hose, watch for exhaust leaks.

    lots of oil will meet the TCW3 and it will survive on that. Again, oil really is a personal choice. I use Penzoil synthetic because...
  7. Replies
    1
    Views
    53

    Welcome to GreebHulk. If buying new CDI, Buy...

    Welcome to GreebHulk.
    If buying new CDI, Buy here : https://www.watercraftsuperstore.net/sbt-cdi-polaris-1200-4010379.html?top_category_code=Polaris-PWC-Parts&json_search=1

    We have had several...
  8. Replies
    10
    Views
    215

    LOL..How much did you pay for it ? . I'd have...

    LOL..How much did you pay for it ? .

    I'd have to factor in the drive to New York. And I'm pretty lazy...focused more on 3 seaters lately.

    Check to see if the ball is stuck or even present. It...
  9. Replies
    21
    Views
    358

    With the readings you reported, the stator needs...

    With the readings you reported, the stator needs to be replaced. Inspect stator when disassembling.
  10. Replies
    10
    Views
    215

    Want to double your money ? The rubber boot,...

    Want to double your money ?

    The rubber boot, usually has an o-ring built into it. Really just seals the impeller,but kinda centers the drive shaft. Most years used just the o-ring. Should be able...
  11. Replies
    21
    Views
    358

    Yes, the hall sensor is part of the stator, on...

    Yes, the hall sensor is part of the stator, on the front of the engine.

    Take a close look to see if the wires are rubbing against a piece of metal. You would get readings like that.
    UNder the...
  12. That's great to hear ! Thankyou for letting us...

    That's great to hear ! Thankyou for letting us know a conclusion to the problem.

    Sometimes a good mechanic has to check stupid stuff just to cross it off the list, really glad it helped you.
  13. Replies
    29
    Views
    264

    The jet pump has a wedge, 4 degrees. Check that...

    The jet pump has a wedge, 4 degrees. Check that it is installed with the thin edge up.

    I didn't know the Virage will porpoise with 2 riders. My Virage TX is fine with my 250lbs, have not had a...
  14. The plug wires can be switched at the coil. The...

    The plug wires can be switched at the coil. The last "mechanic" I fixed problems for caused a ski to be sold for 10% it value because of plug wires.

    Spark+fuel+compression =running engine unless...
  15. Welcome to GreenHulk. Sounds to me like the plug...

    Welcome to GreenHulk.
    Sounds to me like the plug wires are switched. install them one at a time on mag cylinder to see if one will fire that cylinder.

    Crank seals leaking would cause a lean...
  16. Replies
    1
    Views
    78

    Glad to hear you got the carbs working pretty...

    Glad to hear you got the carbs working pretty well.
    The 700 engines should turn around 6700 in great conditions-temp and humidity matters.

    Yeah, the oil lines are kinda calibrated by how many...
  17. Replies
    25
    Views
    447

    I agree, time to plug in a coil and plug wire.

    I agree, time to plug in a coil and plug wire.
  18. Replies
    25
    Views
    447

    Was the stator ground wire bolted to the steel...

    Was the stator ground wire bolted to the steel bracket that the ground spades connect to ?
    Pretty sure the coil and CDI will also have eyelets that bolt down with stator wire.
  19. Replies
    5
    Views
    120

    Also plug wires and boots.

    Also plug wires and boots.
  20. Replies
    25
    Views
    447

    Good job so far, but looks like you have a few...

    Good job so far, but looks like you have a few problems to deal with.
    The 9v on brown while cranking is a bit higher then usual but should be OK.
    I would look closely at the in-line stator...
  21. Welcome to GreenHulk. My Hurricane would do...

    Welcome to GreenHulk.

    My Hurricane would do that when really low on gas. Air would mix in with fuel.
    Make sure all fuel lines/switch are sealed good, not leaking air.

    Possible for air leaks...
  22. Did you try applying the choke ? Choke at...

    Did you try applying the choke ? Choke at different amounts will cause a richer mixture.

    Running on trailer in water , spray carb cleaner when bogging.

    Could have air leaking in at fuel switch...
  23. Replies
    2
    Views
    57

    The 98 700's used 38mm carbs. Pop off is 18-20...

    The 98 700's used 38mm carbs. Pop off is 18-20 psi.
    Have a look through this;...
  24. Welcome to GreenHulk. No, the coil is not like a...

    Welcome to GreenHulk.
    No, the coil is not like a automotive coil.

    You should see like 70v DC while cranking on yel/brn,blk/grn,blk/blu. The blk/wht is like a return to the CDI.
    I recently had a...
  25. Replies
    6
    Views
    182

    It might just be the picture, but is the pump...

    It might just be the picture, but is the pump exit nozzle opened up? Should be a cast-powder coated smooth piece.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4