Search

Type: Posts; User: Waveraider12

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    743

    no being a smart ass but why a lower cr . Are you...

    no being a smart ass but why a lower cr . Are you only running 91 oct or what fuel , I'm lost what is your intent with ski racing it just a toy to go play with the guys .how much boost there is a lot...
  2. Replies
    15
    Views
    910

    yes it is

    yes it is
  3. check fuel pressure 58-68 psi .

    check fuel pressure 58-68 psi .
  4. Replies
    3
    Views
    271

    there are mods for that and nothing wrong with...

    there are mods for that and nothing wrong with 250 x just do oil change and up grade jet pump check valves once and a while look in the tec tip section you will find the mods .
  5. Replies
    24
    Views
    931

    great job sounds like this is solved .

    great job sounds like this is solved .
  6. Replies
    24
    Views
    931

    good find i hate when that happens hope she is...

    good find i hate when that happens hope she is fixed.
  7. Replies
    5
    Views
    812

    FS - Parts if you have intercooler in a week i will be...

    if you have intercooler in a week i will be interested in it . im out of Ontario Canada.
  8. Replies
    24
    Views
    931

    well that sucks ass . I'm wondering if you leave...

    well that sucks ass . I'm wondering if you leave it on trailer and test it , I'm thinking your problem is when boost is coming on i think its pushing at head gasket below 5000 not to much stress on...
  9. Replies
    24
    Views
    931

    so lets go throw head torque 15ft 30ft (120)...

    so lets go throw head torque 15ft 30ft (120) degree and (90) degree after right if you only torqued it to 90 ft pounds this is your issue . one other thing to check is coolant strength if its set...
  10. Replies
    24
    Views
    1,063

    i love my ultra 250 x i see you drive a polaris...

    i love my ultra 250 x i see you drive a polaris this thing is twice the ski in rougher water i had a polaris loved it but this thing is a beast compared to it , you do get a little wet on it but shit...
  11. easy fix cut off old junk tig on new peace.

    easy fix cut off old junk tig on new peace.
  12. Replies
    2
    Views
    212

    thanks i will

    thanks i will
  13. Replies
    2
    Views
    212

    any one use ajust -a thrust

    like the title says any one use adjust - a thrust from wet wolf looked interesting. I ordered one to give it a try
    http://www.wetwolf.com/kaw/ check it out .
  14. Replies
    7
    Views
    438

    if bearings in pump are good that's good news if...

    if bearings in pump are good that's good news if they fail it can put pressure on main thrust bearing till it fails. know as for running poor id start with a fresh set of plugs make sure you are...
  15. Replies
    7
    Views
    438

    they engines' only have issues if jet drive...

    they engines' only have issues if jet drive shits the bed pushes on the crank till it fails id check there did your jet pump have updated shaft and bearings. ?
  16. Replies
    10
    Views
    424

    get updated parts which has been said it will...

    get updated parts which has been said it will save your motor you will need a NEW PROP for sure not a hard job at this point you can run a grease in it or a gear oil.
  17. know i don't know any thing about your engine....

    know i don't know any thing about your engine. but do you just kill it right away if so maybe a little idle time to get cylinder temps back down might help. maybe to much octane some times it can not...
  18. i do be leave you can on thread the coupler and...

    i do be leave you can on thread the coupler and slide shaft out .
  19. The lighter the ski the faster ,when you are...

    The lighter the ski the faster ,when you are talking over 200 pounds that is a lot of weight. but weight give a good ride and takes a good hit in rough water . iv drove the older stuff and my 250 x...
  20. make sure to set your valves this is a huge step...

    make sure to set your valves this is a huge step you dont want to miss.
  21. Replies
    12
    Views
    517

    ow im not saying you must use lock tight i do i...

    ow im not saying you must use lock tight i do i like the safety cushion, just my idea .not for every one and if any of use lock tight just a little heat will let it loose .
  22. Replies
    6
    Views
    326

    10-40 amsoil marien good oil vr1 good oil . as...

    10-40 amsoil marien good oil vr1 good oil . as for filther pick your posion . just keep the oil changed or you will run into problems. and depending on hr have your valves checked droping one would...
  23. Replies
    12
    Views
    517

    ps and make sure you locktight the impeller too...

    ps and make sure you locktight the impeller too or a bunch of bad stuff will happen ow make sure your impeller to wear ring is 2-8 thousands service limit is 20 thousands this helps a lot with...
  24. Replies
    104
    Views
    5,455

    looks super awsome great job

    looks super awsome great job
  25. Replies
    12
    Views
    517

    yes do it and add the exstra bearings to the front

    yes do it and add the exstra bearings to the front
Results 1 to 25 of 43
Page 1 of 2 1 2