Search

Type: Posts; User: Bigbill55

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Emm repair

    by Bigbill55
    Replies
    46
    Views
    6,039

    I had 2 of my EMM's repaired by the same place...

    Is there an impact on recommended fuel octane?[/QUOTE]

    I had 2 of my EMM's repaired by the same place this month. The only reccomendations to were to use atleast 91 octane (I always do), and to...
  2. MSX 140 Speed sensor wierd issue, what's going on?

    Here's my issue. I finally have my 03 MSX up and running. When I got it out, it will not register the speed. The display stays at zero. I did some reading, and checked the wheel while it was on the...
  3. Update! The MSX is alive!!! I found the issue. I...

    Update! The MSX is alive!!! I found the issue. I would like to thank everyone who has commented on this thread, as it has been a big help. What it ended up being, is what Keith said to check. I did...
  4. It was a seat bumper... for my Virage

    How big is it?

    Bumper for under the seat?[/QUOTE]

    It was a seat bumper... for my Virage
  5. 361840361839 I found this on the ground behind...

    361840361839

    I found this on the ground behind the MSX. What is it? Does it even go to the Jet Ski?
  6. What is the specs on the capacitor? I have one in...

    What is the specs on the capacitor? I have one in my Pinball machine, that looks very similar (I know this means nothing), but if they have the same voltage/uf rating, I could use that one to test. I...
  7. K447 "Check the loop-through diagnostic connector...

    K447 "Check the loop-through diagnostic connector pair. There is a four pin Deutsch connector with ONLY a white/red wire on one side and four wires on the other."

    This is where I checked for...
  8. I will clean all my ground connections when I get...

    I will clean all my ground connections when I get home. I do think they are good, as when I checked resistance I measured from the batt ground, to an injector mounting bolt, and had continuity (.5...
  9. I snuck home for lunch. Here is my voltages: ...

    I snuck home for lunch. Here is my voltages:

    Stator (as measured from the 12 pin connector):

    Pins 1 - 12 = 7.52 VAC
    Pins 2 - 11 = 7.70 VAC
    Pins 3 - 10 = 4.98 VAC
    Pins 4 - 9 = 5.17 VAC...
  10. I do have one more question. On my Virage, I...

    I do have one more question. On my Virage, I noticed that I can crank over the motor with the lanyard removed. The engine won't start, but it will turn over. On my MSX, it won't turn over unless my...
  11. I was using an AGM battery. It started to crank...

    I was using an AGM battery. It started to crank slow (after many attempts to try and start it), so I changed it out with a brand new lead/acid battery, fully charged. It didn't change anything. I...
  12. I haven't checked those yet. The sun went down. I...

    I haven't checked those yet. The sun went down. I will check those tomorrow, after work, and report my findings. Thanks for all the help everyone!
  13. I did check that, and it was plugged in. I put it...

    I did check that, and it was plugged in. I put it into the Virage, and it works in it. Put it back into the MSX, and no spark. Thanks for the thought!
  14. Thanks for the advice. I will check those...

    Thanks for the advice. I will check those tomorrow, and report my findings.

    To recap what happened, I was putting around, then hit the throttle. The ski jumped right up, got to about 45 mph, then...
  15. Here's what I have checked on my MSX, it was...

    Here's what I have checked on my MSX, it was running, then died. No spark.

    EMM into another machine, starts right up
    Crank sensor into another machine, starts right up
    Ohmed out Stator with the...
  16. Well, my troubles continue. I got my EMM back...

    Well, my troubles continue. I got my EMM back from the repair shop, and put it in the ski. Started right up!!! Brought it out to the lake, let it idle on the trailer for about 15 mins, to get nice...
  17. MSX 150 MFD into a MSX 140 Will it work?

    I was wondering, if I could put my MSX 150 Display into my MSX 140. I do realize, that the "Turbo", would actually be the oil level, if they are interchangeable. Just wondering, if it is that simple,...
  18. Replies
    3
    Views
    396

    WTB - Parts Thanks!

    Thanks!
  19. Replies
    3
    Views
    396

    WTB - Parts Fire extiinguisher

    WTB Fire extinguisher 'for my 03 MSX 140.

    Thanks.
  20. Thanks for the information. I will not mill the...

    Thanks for the information. I will not mill the heads, and keep the engine stock. I will also not get the upgrade for the EMM. Thanks. Very good points.
  21. Got a re-plated cylinder, and new piston/rings....

    Got a re-plated cylinder, and new piston/rings. Compression is now 124 - 118 -119. Put together, no fuel pressure. Pulled fuel pump assy. FPR was on bottom. Fixed that. Put back together, no fuel...
  22. Replies
    20
    Views
    2,084

    PM sent

    PM sent
  23. Replies
    20
    Views
    2,084

    How much for the motor?

    How much for the motor?
  24. FS - Parts The hour meter on the Display says 62. I can't...

    The hour meter on the Display says 62. I can't verify if the motor has been rebuilt, but the flywheel had a paint pen marking on it saying May 06. I can take the case apart, and send pics if you'd...
  25. Replies
    3
    Views
    463

    Thanks for the advise. I won't waste my time...

    Thanks for the advise. I won't waste my time mixing the gas. I'll search on here tomorrow on how to check alignment for the engine/jet pump.
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4