Search

Type: Posts; User: SKEricsson

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    2,246

    Well, you can, but as he stated above - if you...

    Well, you can, but as he stated above - if you want the full potential out of the pipes, make the suggested mods. What these pipes will do for you is open up the back end of the motor allowing far...
  2. Replies
    8
    Views
    2,903

    Yes, they ride low, especially at idle. I notice...

    Yes, they ride low, especially at idle. I notice I push a lot of water up over the front when idling out, but once on the gas, it jumps up and planes nicely. My XL760s both ride much higher and...
  3. Replies
    58
    Views
    46,224

    Sticky: Glass beading is fine if you do the proper...

    Glass beading is fine if you do the proper cleaning afterward to remove any leftover glass, which as I read it, he certainly did do. I love my blast cabinet, I use it for everything practically. ...
  4. Replies
    9
    Views
    1,017

    Isn't it amazing how the most complicated looking...

    Isn't it amazing how the most complicated looking things can turn out to be so simple? Nice, let us know what you find!
  5. Replies
    9
    Views
    1,017

    As The Great Scot says, pull the cover on the...

    As The Great Scot says, pull the cover on the ebox. There are quick connectors inside that disconnect the stator wires, then a couple of nuts for the grounds. There are two green wires also that...
  6. Thread: Good price?

    by SKEricsson
    Replies
    11
    Views
    1,092

    I'd try $2500, all he can do is say no.

    I'd try $2500, all he can do is say no.
  7. Thread: Good price?

    by SKEricsson
    Replies
    11
    Views
    1,092

    It might be, but what are they asking for it?? ...

    It might be, but what are they asking for it?? Take it for a ride and if it runs and rides great, you're halfway to a good deal. The other half is what you can get it for.
  8. Replies
    6
    Views
    2,886

    GP1200 hull weight?

    This winter the GP1200 is getting stripped down to the hull to clean up inside and fix some water leaks and damage to the bottom and re-gelcoat. Any idea how heavy the bare hull is?
  9. Replies
    49
    Views
    10,931

    Great deal for someone, any interest yet? How...

    Great deal for someone, any interest yet? How many hours you figure you've put on it in two years?
  10. Replies
    49
    Views
    10,931

    Nice! How much are you asking?

    Nice! How much are you asking?
  11. Replies
    9
    Views
    3,638

    Well thanks for all the responses gentlemen, she...

    Well thanks for all the responses gentlemen, she ran great today! I'm sure the clogged lines were the issue, I had much stronger streams out of the pissers. The other issue is the fuel I was using...
  12. Replies
    9
    Views
    3,638

    Hey Johnny, thanks for the info! I had to do a...

    Hey Johnny, thanks for the info! I had to do a little research to find out what the stingers are, HAH!!! I'm such a newb.... But, I looked it up and from what I could remember when I had the pipes...
  13. Replies
    9
    Views
    3,638

    Thanks Lakemotox, I will ride it again this...

    Thanks Lakemotox, I will ride it again this afternoon or tomorrow, if it does it again it's coming apart this winter.
  14. Replies
    9
    Views
    3,638

    So here's what I found so far. This is the...

    So here's what I found so far.

    This is the particle screen inside the triple pipe water distribution manifold

    http://www.greenhulk.net/forums/images/imported/2009/09/380.jpg

    I've noticed...
  15. Replies
    9
    Views
    3,638

    On second look at it my memory is refreshed, the...

    On second look at it my memory is refreshed, the cooling water enters the head next to each exhaust port, fed by three hoses off the triple pipe water distribution manifold, or whatever they call it....
  16. Replies
    9
    Views
    3,638

    97 GP1200 Factory Pipe triple overheating

    So here's the deal. I have a '97 GP1200 with Factory Pipe triple pipes, Riva stage II. So I had to change a stator and flywheel because the RAD flywheel I had grenaded. I think it was already shot...
  17. Replies
    1
    Views
    844

    Aluminum thru hull fittings?

    My FP triple ski has some nice aluminum fittings for the water ports, but one was missing when I bought the ski. I have a brass elbow on it now, but where can I find these??
  18. Replies
    3
    Views
    694

    Might have been grass, which can wrap up in the...

    Might have been grass, which can wrap up in the impeller and you can't see it. Eventually it can work loose and you're fine. Did you look in the nozzle to see if the impeller was clear?
  19. Hah, yeah, drain plug. Done it before - TWICE!! ...

    Hah, yeah, drain plug. Done it before - TWICE!! Now I have an automatic 500GPM bilge pump just in case I get stupid again......
  20. Replies
    64
    Views
    7,838

    HAH!!! Me either, but I imagine if you did rape...

    HAH!!! Me either, but I imagine if you did rape an ape, it would sure as hell rip your arms off!!

    I think the real problem with the GPs and Yamahas in general, from what all the mechanics tell...
  21. Replies
    49
    Views
    10,931

    Curious if you got a new flywheel? Here is what...

    Curious if you got a new flywheel? Here is what mine looks like now....

    http://www.greenhulk.net/forums/images/imported/2009/09/230.jpg
    ...
  22. Replies
    64
    Views
    7,838

    Just to throw my $.02 in to the mix, I have a '97...

    Just to throw my $.02 in to the mix, I have a '97 GP1200 built and bored with Factory triples and to ride it compared to my stock skis is a stunning experience. I didn't build it, just bought it. ...
Results 1 to 22 of 22