Search

Page 1 of 9 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    19
    Views
    701

    View Post

    I donít know why people lock them at the house.. the only time I lock mine is when on the water at a restaurant where I canít see it from the restaurant
    I keep 1 fob in a water proof case with my...
  2. Replies
    10
    Views
    315

    I doubt that a charger like that will generate...

    I doubt that a charger like that will generate much heat. The battery is kept fully charged almost all the time. A maintainer will let it discharge and recharge it periodically, but you probably...
  3. Replies
    10
    Views
    437

    Normal. They all do that. The play is in the...

    Normal. They all do that. The play is in the portion of the steering that makes it height adjustable. Your fine. Only way to have a solid setup with no play what so wver is a billet non adjustable...
  4. Replies
    74
    Views
    8,219

    2021. Talked to my dealer and Yamaha hasnt done...

    2021. Talked to my dealer and Yamaha hasnt done anything about it yet as far as he knows. When you access the plate on the yamaha parts page you can see the part number but cannot order the part. ...
  5. Replies
    7
    Views
    562

    I agree with going by rotation after seated by...

    I agree with going by rotation after seated by hand but one important note is there's a big difference between brand new plugs with un-crashed washer and one that has been previously installed and...
  6. Replies
    74
    Views
    8,219

    I agree, because Yamaha never advertised that the...

    I agree, because Yamaha never advertised that the "transom plate" was 160mm. That is something that I learned while at the press introduction when I rode the ski and I passed on to the forum members...
  7. Replies
    74
    Views
    8,219

    Take ski to your dealer, they will verify the...

    Take ski to your dealer, they will verify the part number and send the info to Yamaha they will make it right. I contacted Yamaha through the yes warranty department the person I spoke to was very...
  8. Replies
    74
    Views
    8,219

    If the 2021 part numbers are not yet available on...

    If the 2021 part numbers are not yet available on the OEM part finder link toward the top of the page then I would roll with the casting number that shhr provided in post #24 above. Call your dealer...
  9. Replies
    74
    Views
    8,219

    I agree, I am going to start trying to contact...

    I agree, I am going to start trying to contact Yamaha directly to see what they have to say.
    Gerry, is this something you can also bring to the attention of any Yamaha folks?

    Can someone...
  10. Replies
    74
    Views
    8,219

    Guys, speaking as a manufacturing engineer this...

    Guys, speaking as a manufacturing engineer this is a big deal. How this slipped thru the quality control process on their assembly line is a big deal. I don't work for Yamaha, but knowing what I know...
  11. Replies
    74
    Views
    8,219

    Ok here is what I have. I have 2 GP1800 one with...

    Ok here is what I have. I have 2 GP1800 one with the date of 9/11 one with a date of 10/13. The 10/13 has the correct transom plate the 9/11 boat has the old style. I have also confirmed 4 other...
  12. Replies
    214
    Views
    148,807

    Sticky: Those tears are pretty substantial. I’d fill them...

    Those tears are pretty substantial. I’d fill them in... there’s ways to do it by gluing foam into the cracks, then glue the vinyl back down.

    There’s also videos by The Jetski Store.
  13. Replies
    20
    Views
    1,723

    Before my first Yamaha hull repair I purchased...

    Before my first Yamaha hull repair I purchased paint kits from from ColorRite (the Yamaha 'official' repair paint source). We have one red and one blue GP1800. I ordered color correct base coat for...
  14. Replies
    39
    Views
    2,172

    Back in the water =)

    So finally after all go it working, and wanted to give an update in case someone in the future finds themselves on this position.

    Also wanted to give thanks to all who chimed in with a posible...
  15. Replies
    7
    Views
    6,868

    I used an independent eye practitioner who sent...

    I used an independent eye practitioner who sent the frames away with the lens order.

    If I was to do it again I would probably let SeaSpec do the prescription lens directly.

    The tricky part...
  16. Replies
    15
    Views
    1,167

    http://greenhulk.net/forums/showthread.php?t=76954...

    http://greenhulk.net/forums/showthread.php?t=76954&page=7&highlight=bomb+proof

    Post Number 64. I built one of these without the wheels. It has been outside on the edge of the woods in my yard...
  17. Replies
    35
    Views
    3,828

    I think you pretty much answered your own...

    I think you pretty much answered your own questions.A 16 degree pitch with a small nozzle is not moving as much water volume and can feel lazy on the bottom end.If you add a tail cone on that setup...
  18. Replies
    4
    Views
    262

    That was it the battery went dead and kicked on...

    That was it the battery went dead and kicked on the security system. Thank you very much for your help
  19. That sounds like the grate is pushing in more...

    That sounds like the grate is pushing in more water than the slowing down pump can process creating mini stuffs.
  20. From a satellite view it may be deceiving, but...

    From a satellite view it may be deceiving, but the canals are pretty wide and clean. Most vegetation (if any) is usually along the shoreline with plenty of space to ride debris free.

    There are...
  21. Replies
    17
    Views
    1,492

    Many of these things have NEVER been greased...

    Many of these things have NEVER been greased since new. On those, the grease has probably hardened inside the hose. Best thing to do if you're not sure if it's been serviced is to remove the hose...
  22. Replies
    18
    Views
    1,284

    Casting resin can be used to fill the hollow...

    Casting resin can be used to fill the hollow voids in the aluminum castings but it would not be used to seal the sections of the jet pump to each other.

    I have used 3M 4200 Fast Cure sealant...
  23. Replies
    11
    Views
    1,565

    View Post

    I wouldnít put a SBT engine on my lawn mower. I used them once and never again.
  24. I had my 2019 FXSVHO re-flashed last week and...

    I had my 2019 FXSVHO re-flashed last week and went on a short ride today. I started with a full tank, using the slow fill method to make sure the tank was actually full. The fuel gauge was reading...
  25. Replies
    37
    Views
    4,516

    OEM is handling what it's designed to do. If...

    OEM is handling what it's designed to do. If aftermarket can't keep up, you may need to ask what you're really trying to accomplish. Anyone running over 94MPH is not recreationally riding their ski,...
Results 1 to 25 of 224
Page 1 of 9 1 2 3 4