Search

Type: Posts; User: HoverRL

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    158

    2005 RXT Missing Issue

    Several years ago I rebuilt (Head rebuild was done by a professional) the head and replaced a piston after a dropped valve. Engine ran great for 20 hours, now after sitting for several years it...
  2. Replies
    111
    Views
    23,884

    Sticky: Starter Cost for 2005 RXT? Also any tips for replacing the starter?

    Hello, any tip for accessing the starter for replacement?
  3. Replies
    23
    Views
    24,901

    Oil Drain Plug on the bottom of the PTO Housing...

    Oil Drain Plug on the bottom of the PTO Housing but very, very hard to access and will dump the oil into the hull. Most operators and shops suck the oil out thru the Dip Stick housing. Compression...
  4. Replies
    6
    Views
    2,239

    Paul I have two Ski's one with the same fuel...

    Paul
    I have two Ski's one with the same fuel display inaccuracy problem. I have swapped the various associated parts i.e.: Sender, Gauges, etc. and can only get the problem to follow with a swap of...
  5. Replies
    10
    Views
    1,335

    Take the sending unit out and bend the float arm...

    Take the sending unit out and bend the float arm down, it will change the indication.
  6. Replies
    10
    Views
    995

    My shaft has very minimal fore and aft movement. ...

    My shaft has very minimal fore and aft movement. If the Tell-tail mark on the shaft is not visible it should be good! I took the ski out for a test yesterday and found that only at high power (RPM)...
  7. Replies
    10
    Views
    995

    In researching alignment (driveshaft) I have been...

    In researching alignment (driveshaft) I have been unable to find any documentation defining "longitudinal axis". Can you provide your link?
  8. Replies
    14
    Views
    1,353

    Oh come on! Haven't we all done something crazy!

    Oh come on! Haven't we all done something crazy!
  9. Replies
    10
    Views
    995

    I appreciate all of your points, I will recheck...

    I appreciate all of your points, I will recheck all of them although everything seems to be in order. The Pump is definitely seated and it would be difficult to get the engine too forward. I used...
  10. Replies
    10
    Views
    995

    I appreciate your response but you may have...

    I appreciate your response but you may have misunderstood the issue. The motor and control of it are fine it runs good. The issue is that somehow the powertrain i.e.: driveshaft disconnects from...
  11. Replies
    10
    Views
    995

    After installing driveshaft.

    I recently had my 2005 GTX motor rebuilt due to a dropped valve. Install went well and driveshaft alignment seemed cool as I ran the machine while on the trailer while backed into the water; no...
  12. Replies
    12
    Views
    1,841

    Supercharger and Head (Valves) O/H an essential! ...

    Supercharger and Head (Valves) O/H an essential! Cheap and I mean CHEAP insurance! I have a 2005 RXT that dropped a valve causing minimal damage but still at a rate of $2,000.00 and I did most of...
  13. Thread: Flywheel Bolts

    by HoverRL
    Replies
    1
    Views
    395

    Flywheel Bolts

    When did Sea Doo go to the new bolts?
  14. Replies
    5
    Views
    817

    I recently installed an Automatic Rule 500 GPH in...

    I recently installed an Automatic Rule 500 GPH in mine with a Rule Auto/Manual Switch. I mounted the actual pump on the Starboard Aft. side next to the driveshaft tunnel on standoffs so that it...
  15. Replies
    0
    Views
    523

    Fuel Tank Hold Down Strap

    One of mine came loose. Any ideas?
  16. Not the correct location. Further back round and...

    Not the correct location. Further back round and sloping.
  17. Thread: Bilge Pump

    by HoverRL
    Replies
    12
    Views
    1,695

    Oh, too much heat?

    Oh, too much heat?
  18. Thread: Bilge Pump

    by HoverRL
    Replies
    12
    Views
    1,695

    Figures some Jersey Donkey would have a problem...

    Figures some Jersey Donkey would have a problem with my response!
  19. Thread: Bilge Pump

    by HoverRL
    Replies
    12
    Views
    1,695

    Not the correct install!

    Not the correct install!
  20. Thread: Bilge Pump

    by HoverRL
    Replies
    12
    Views
    1,695

    Bilge Pump

    Someone posted a install for a bilge pump with the controls in the glove box. I can't find that post! Can anyone help?
  21. Replies
    4
    Views
    531

    The Fuel Sensor doesn't interface with the ECU,...

    The Fuel Sensor doesn't interface with the ECU, only the Pump.
  22. Replies
    4
    Views
    531

    I checked the resistance. no problem.

    I checked the resistance. no problem.
  23. Replies
    14
    Views
    6,910

    HoverRL, fiveskid@aol.com, could I get the bilge...

    HoverRL, fiveskid@aol.com, could I get the bilge pump setup and pictures also.

    Thanks
  24. Replies
    14
    Views
    6,910

    Could I get the bilge pump pictures also? ...

    Could I get the bilge pump pictures also?

    Thanks,
    Roger
  25. Replies
    4
    Views
    531

    2005 GTX Fuel Indication Issue

    No level indication and a intermittent beep indicating low level, no matter the level in fuel tank. Replaced the level sensor with no change. I noticed that the signal from the sensor is wired to...
Results 1 to 25 of 37
Page 1 of 2 1 2