Search

Search: Search took 1.00 seconds.

  1. Replies
    18
    Views
    1,080

    I all ready got it, and used it before posting. ...

    I all ready got it, and used it before posting.

    its aluminum, fits and works... not sure what else to say. I can take a pic of it on a clutch sprocket if you want. But its not some moving part...
  2. You might find it informational to bounce this...

    You might find it informational to bounce this email (specifically the years of when parts shifted) off a thread I did a few years back. Not saying it's wrong, just that folks memory get fuzzy (me...
  3. 05-17' VXR / GP1800 EASY Intake Grate Insert Removal

    2015-17 VXR owners and 2017-18 GP1800 intake grate rear insert removal. I figured I'd share my experience removing these, and just how easy of a job it can be. The pictures pretty much sum it up. I...
  4. Replies
    6
    Views
    587

    test results

    Just went for a test run. I can say for sure there were NO ill effects. In fact it was an improvement. I feel like with the turn nozzle internal side to side width increased, the steering was...
  5. Thread: Paint bubbles

    by seabrook
    Replies
    36
    Views
    1,573

    My hood...

    My hood http://greenhulk.net/forums/attachment.php?attachmentid=448337&stc=1
  6. Replies
    9
    Views
    679

    I would consider another oil change shortly, if...

    I would consider another oil change shortly, if you take the clutch apart you will see the sprag and roller bearings have a lot of wear on them and that worn off metal may all be in the filter but...
  7. Replies
    41
    Views
    2,631

    Ok, ski is back together and ready to test... ...

    Ok, ski is back together and ready to test...

    hand packed bearing with marine quicksilver grease, and loaded it on both sides heavy before pressing In each oil seal, then squirted more in the gap,...
  8. Replies
    41
    Views
    2,631

    Rodger that, swap alignment pins i plan to...

    Rodger that, swap alignment pins

    i plan to hook up hose and pump grease from my zerK fitting, through hose, and into housing..so I know the whole system is loaded...then

    install rear C clip-...
  9. Replies
    41
    Views
    2,631

    superair - thanks for the correction on the press...

    superair - thanks for the correction on the press direction - it been a while since I did mine.
    I do remember a need to remove it however, and I want to say I needed to because otherwise it was near...
  10. Replies
    3
    Views
    396

    Thanks superair, impeller looks perfect and...

    Thanks superair, impeller looks perfect and bearings good. have done grinding with dremel tool, now has clearance of 0.007". Has anyone used the plastic lined pump housings as a replacement?
  11. Replies
    35
    Views
    2,369

    for now...lol

    for now...lol
  12. Sticky: This should be a sticky. Simplest solution I...

    This should be a sticky. Simplest solution I have seen yet.
  13. Replies
    2
    Views
    487

    Never remove or install a cam as shown in the...

    Never remove or install a cam as shown in the video. All caps per single cam need to be worked down together to distribute the spring tension. That is exactly how you break a cam.
  14. Pressurized the coolant system - leak found

    Hey, just wanted to quickly share how I was able to successfully find a pesky leak on a 1.8 NA (VXR) recently. . .

    This leak has been plaguing me for quite some time. Started out with just a...
  15. Replies
    13
    Views
    1,355

    Place shim on top of the valve and make sure it...

    Place shim on top of the valve and make sure it is seated properly before installing the bucket.
  16. Replies
    63
    Views
    10,924

    Ultramax, I believe the whole GreenHulk...

    Ultramax,
    I believe the whole GreenHulk community is relieved your ok and prays for a speedy recovery
  17. Thread: FZR Cooling

    by JD 1
    Replies
    91
    Views
    20,132

    No. You can use that..

    Ok yeah I'm not adding the cooling plate, so that means just leave the abode in and just take out my thermostat?[/QUOTE]

    Yep[/QUOTE]

    Nice then that makes it cheaper and one less hole to drill...
  18. Of course!

    Of course!
  19. Replies
    22
    Views
    2,717

    IMO I doubt it's the ECU, feel around the bov is...

    IMO I doubt it's the ECU, feel around the bov is the oring installed?? Your not producing boost hence you are losing it somewhere!! Make sure that bov is operating correctly if it is not closing shut...
  20. Replies
    8
    Views
    2,852

    I'm curious to know what he told you would be...

    I'm curious to know what he told you would be better lol..


    The supercharger is not the issue. It's the supercharger clutch. They are known to go bad depending on how you ride. Upgrade to the...
  21. Replies
    20
    Views
    2,979

    See my signature for my stats. I'm thinking...

    See my signature for my stats. I'm thinking about selling my R2 and maybe going with the Athena.....
    There is more to get I've been told once I repitch my prop. I would prefer not to go much more...
  22. Replies
    23
    Views
    27,845

    Sticky: i'm dealing with this on an old waverunner 3. ...

    i'm dealing with this on an old waverunner 3. is the intermediate shaft hollow all the way through? i assume so since you said you can spray wd40 in the engine end and it will soak down into the...
Results 1 to 22 of 24