Search

Type: Posts; User: philbbar715

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    287

    I have a 2010 GTX 155 and would like to see how...

    I have a 2010 GTX 155 and would like to see how easily it would be to install the larger 18.5gal tank too. Is there any particular part # i should be looking for?
  2. I love that mounting! On the SeaDoos the...

    I love that mounting! On the SeaDoos the rideplate is used as a heat exchanger so i cant screw through it to mount the transducer. However I may try some epoxy/sealant/glue and glue it on the...
  3. I picked the location where there are no...

    I picked the location where there are no strakes/steps/ridges and away from the rideplate. Basically halfway between the rideplate and far right edge of the transom. Its hard to tell from my photo...
  4. I have a Lowrance Hook Reveal mounted on my GTX...

    I have a Lowrance Hook Reveal mounted on my GTX 155. I am having an issue with the transducer reading at speed. As soon as I get on plane I get issues with it holding bottom. It looks like everyone...
  5. Replies
    12
    Views
    644

    I just wanted to thank everyone again in this...

    I just wanted to thank everyone again in this thread! I took the ski out this afternoon for the first time since replacing the wear ring and it runs perfectly! Top speed is back and no cavitation on...
  6. I recently purchased a single 2010 GTX 155...

    I recently purchased a single 2010 GTX 155 (236hrs) in February from a guy in Maryland. I paid $3600 for the ski, it was in very poor visual condition. Very dirty, oxidation on hull, inside of hull...
  7. Replies
    12
    Views
    644

    Before I had the suggestion of the bolt extractor...

    Before I had the suggestion of the bolt extractor i thought by taking off those pump supports it would allow me to take the whole pump out without having to get the stripped bolt free. I was wrong...
  8. Replies
    12
    Views
    644

    Carbon seal is good so far (no leaks and no...

    Carbon seal is good so far (no leaks and no dust). Agreed that the driveshaft itself is corroded however the splines in to the pump look perfect and the visible portion of the shaft inside the hull...
  9. Replies
    12
    Views
    644

    Yep the harbor freight extractor worked well! I...

    Yep the harbor freight extractor worked well! I was afraid that since the HF extractors arent tapered like the ones posted in the above link to amazon they would just round off the head. But it...
  10. Replies
    12
    Views
    644

    Thanks for the bolt extractor suggestion! That...

    Thanks for the bolt extractor suggestion! That worked!! With lots of heat and pounding one on i was able to get the bolt out.

    Now I have another problem. No matter how much I pull, the pump will...
  11. Replies
    12
    Views
    644

    Pump Bolt Stripped on Ride Plate

    I have a 2010 GTX 155, I am replacing the wear ring and inspecting the driveshaft for wear as it has the original 2010 driveshaft that was prone to issues. I have the IBR, VTS, and steering all out...
  12. Replies
    8
    Views
    345

    im assuming this is the dreaded 2010 original...

    im assuming this is the dreaded 2010 original shaft? Since this is the 155, is 10 years old, and has been 237hrs it should have failed by now right? I dont really feel like spending $400 to replace...
  13. Replies
    8
    Views
    345

    In this photo, which one of the clamps do i need...

    In this photo, which one of the clamps do i need to loosen and pull back the rubber housing? The boot itself is very clean, shiny, and new looking (newest looking piece in the ski honestly). And yes...
  14. Replies
    10
    Views
    510

    Yep, I saw lots of black on the pad when I was...

    Yep, I saw lots of black on the pad when I was buffing. So black that I had to rinse it off every few min. Same thing when I did the top, lots of white. The pad was orange so it was easy to see the...
  15. Replies
    8
    Views
    345

    2010 GTX 155 Driveshaft

    I reticently purchased a used 2010 GTX 155 with 237hrs. Ive read that the 2010s have issues with the driveshafts stripping. How can I tell if I have the original shaft? Ive already looked under the...
  16. Replies
    10
    Views
    510

    I wanted to give an update. I bought a cheap...

    I wanted to give an update. I bought a cheap polisher from amazon, cheap rubbing compound, meguiar's marine wax and went to town. I started off with the polisher and foam pad, and rubbing compound...
  17. Replies
    10
    Views
    510

    Thanks for the advice! I tried some rubbing...

    Thanks for the advice! I tried some rubbing compound on a buffing pad on my dremel. Other than it only working on a small spot at a time it worked great and removed the oxidation! You can see it in...
  18. Replies
    10
    Views
    510

    Thanks guys! Should I use these products by hand...

    Thanks guys! Should I use these products by hand or should I get a buffer of some kind?
  19. Replies
    10
    Views
    510

    Easy Way to Clean Hull

    I have some oxidation/staining on a 2010 GTX 155 that I recently purchased. It has about 237hrs on it but I think the previous owner neglected and left it sitting out. Is there an easy way to get...
  20. Replies
    2
    Views
    201

    Thanks will do!!

    Thanks will do!!
  21. Replies
    2
    Views
    201

    2010 Sea-Doo GTX 155 Repair Manual

    I purchased a used 2010 GTX 155 2010 today and am looking to buy a fulll repair/service manual.

    On https://brpmanuals.com/seadoo-manual.htm I see 2009 and then 2011 manuals, and for 2010 they...
  22. Replies
    0
    Views
    169

    Deciding on First Skis

    I would like to buy two used skis, one for my wife and one for myself. I am very mechanically inclined and dont mind doing maintenance/repairs/upgrades/ect myself. We live in VA in the hampton roads...
Results 1 to 22 of 22