Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    136

    The one I have is from a '92. It slips onto studs...

    The one I have is from a '92. It slips onto studs and has pipe nipples VERY much like a 2 stroke Seadoo pump.
  2. On one that takes off fast then slows down or...

    On one that takes off fast then slows down or surges......the first thing I check for is water in the intake tube to the throttle body......bad intercooler.
  3. That's what I'm wondering. Is it possible an...

    That's what I'm wondering. Is it possible an injector or fuel rail was leaking and it was a flash fire instead of a major overheat? I worked on an RXT this year that would start bogging and rough...
  4. Replies
    7
    Views
    136

    I might have an extra 650 pump here,...freshwater.

    I might have an extra 650 pump here,...freshwater.
  5. The Rfi will not overheat if you bypass the...

    The Rfi will not overheat if you bypass the cooler completely. What WILL happen is a shorter lifespan of the crank bearings. On a carbed machine, the incoming fuel charge helps keep the bearings...
  6. Replies
    3
    Views
    190

    Try watching the drain and unplugging other...

    Try watching the drain and unplugging other things. I've seen bad gauges cause enough current draw to kill a battery in a couple days.
  7. Easy peasy. Take off the line on the front of the...

    Easy peasy. Take off the line on the front of the head. Clamp off the part going to the pipe. Funnel a bit of antifreeze in and blow through it. The ONLY passage is through the stator cooler and on...
  8. I think so too. I've done oil changes on 20 and...

    I think so too. I've done oil changes on 20 and 30 hour machines that still had that much.
  9. Replies
    3
    Views
    120

    WTB - Parts Yep....it's a unicorn. I've got one here taken...

    Yep....it's a unicorn. I've got one here taken apart with stator in great shape, no internal bearing area issues. I will take $150 shipped in the cont. US.
  10. Replies
    2
    Views
    113

    Thanks bro.

    Thanks bro.
  11. Replies
    9
    Views
    560

    I'll probably just haul all mine to scrap this...

    I'll probably just haul all mine to scrap this winter. At least I'll get a few bucks.
  12. Replies
    2
    Views
    113

    GP1200r GP1300r cylinder temps

    Can anybody tell me the typical temps of a triple GPR after warmed up and idling? I know it depends on the water temp but I'm seeing about 10-12 degrees warmer on the front cylinder. I know that's...
  13. Replies
    2
    Views
    166

    Sure sounds like a head gasket.....I guess you'll...

    Sure sounds like a head gasket.....I guess you'll have to pull it to find out. I just did one on a 300x and couldn't find anything as to why it happened. New gasket and running good.
  14. Replies
    1
    Views
    111

    Check with Westside Powersports. They've been...

    Check with Westside Powersports. They've been parting out Seadoos for years.
  15. Replies
    1
    Views
    342

    I recently cut one open in an attempt to repair...

    I recently cut one open in an attempt to repair it. The reason nobody is offering repair on that style gauge is because the polarizer film that gets sunburnt is on the BACK side of the glass! That...
  16. Replies
    1
    Views
    147

    You should NOT hear bubbling when blowing into...

    You should NOT hear bubbling when blowing into the return line. The return dumps out freely into the top of the baffle. The tank would have to be filled up to the neck to hear bubbling! Check the...
  17. Replies
    3
    Views
    152

    Threebond if the surfaces are scratched or pitted...

    Threebond if the surfaces are scratched or pitted up. Otherwise clean surfaces with new gaskets require nothing, just assemble dry. If you just want extra insurance the copper spray is great.
  18. Thread: 255 rebuild

    by Myself
    Replies
    4
    Views
    318

    Yep,.....the service manual. Everything is in it...

    Yep,.....the service manual. Everything is in it and pretty well written. Any hangups or things you don't understand can be asked on the forum and somebody will have an answer. All I can think of...
  19. Replies
    1
    Views
    118

    Ohm the primary side (where the connector hooks...

    Ohm the primary side (where the connector hooks up), should be low ohms, like around 1-1.5 ohms.
    Ohm the secondary (what touches the spark plug). One lead there and one to either side of the...
  20. Replies
    4
    Views
    287

    Sometimes an ECU goes bad. The last one I sent...

    Sometimes an ECU goes bad. The last one I sent for repair was keeping one injector open and flooding a cylinder. If it's actually doing this it will hydrolock. Black plugs are just very rich not...
  21. Replies
    17
    Views
    744

    Sorry, yes. Basically just step back and watch...

    Sorry, yes. Basically just step back and watch for pink instead of clear in the general area under the pump. A bit will spit out of the exhaust, a bit will spit out of the pissers, and of course from...
  22. Replies
    7
    Views
    369

    What?!! You must ride like a grandma lol!

    What?!! You must ride like a grandma lol!
  23. Replies
    17
    Views
    744

    I also use the flush ports. I have a garden hose...

    I also use the flush ports. I have a garden hose fitting clamped to a 2ft length of hose. Screws right into a 'Doo and Kawi, and into the adapter on a Yamaha. On the Yamaha I also use a pair of hose...
  24. LOL! I was going to say the exact same thing....

    LOL! I was going to say the exact same thing. 2009 or newer with a non supercharged 1.8L. I'd go for the Cruiser with the hip support seating but don't let it be a deal breaker cause you can always...
  25. Replies
    4
    Views
    287

    Most likely throttle cable mis-adjusted and TPS...

    Most likely throttle cable mis-adjusted and TPS giving the ECU signal to enrich the mixture. Check that there is slack in the cable and that all the hoses to the IAC motor are hooked up.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4