Search

Type: Posts; User: tiderider

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. I check clearance with a bore gauge. Just to let...

    I check clearance with a bore gauge. Just to let you know that if your crankshaft journals are within specs, using WSM bearings work well for clearances at a fraction of the cost to OEM with the same...
  2. Crankshaft Pin maximum 45.048 1.7735 Crankshaft...

    Crankshaft Pin maximum 45.048 1.7735
    Crankshaft Pin Minimum 45.032 1.7729
    Crankshaft Pin Service limit 45.029 1.7728

    Crankshaft Pin Radial Clearances service limit 0.09 0.0035
  3. Replies
    1
    Views
    97

    If you have a candoo, you can test each injector...

    If you have a candoo, you can test each injector for function.. It can be wiring/connections or ECU.
  4. Replies
    3
    Views
    102

    Either a bad head gasket or oil cooler.. Any...

    Either a bad head gasket or oil cooler.. Any coolant mixing with the engine oil?
  5. Replies
    4
    Views
    267

    I can say that WSM bearings are good. I installed...

    I can say that WSM bearings are good. I installed a full set and clearances were perfect.
  6. Replies
    16
    Views
    516

    I'm pretty sure not all Siemens ECU can be...

    I'm pretty sure not all Siemens ECU can be tuned.. I have many logs to prove so..
  7. Replies
    16
    Views
    516

    I wouldn't waste your money trying to tune an...

    I wouldn't waste your money trying to tune an older Siemens ECU... No one can.. From my experience it was a 2007.
  8. Replies
    22
    Views
    500

    Tap on the retainers with the back handle of a...

    Tap on the retainers with the back handle of a hammer. You should hear the valve go in sligthly, it may take 2 tries sometimes. The single groove keepers make this much simpler.
  9. Replies
    20
    Views
    724

    That impeller bolt is part of the oil pump shaft,...

    That impeller bolt is part of the oil pump shaft, probably a good idea to replace as well.
  10. Replies
    22
    Views
    500

    Just tap on the valve stem's top a few times and...

    Just tap on the valve stem's top a few times and then try removing. Works every time.
  11. Replies
    22
    Views
    500

    Clean the threads on the crankshaft with a...

    Clean the threads on the crankshaft with a contact of some sort so the loctite sets fully when you install the flywheel bolts.
  12. The opening on the cylinder head for this nipple...

    The opening on the cylinder head for this nipple is 5mm. Hose is 1/4 inch.. Any guess to where they can be purchased as aftermarket?
  13. Thread: Engine Paint

    by tiderider
    Replies
    7
    Views
    340

    Its all about the prep work. I used Rustoleum...

    Its all about the prep work. I used Rustoleum high temperature with the mat black option. Holds strong now for years.
  14. Replies
    0
    Views
    63

    2007+ OEM 4tec valves issues?

    Any issues with the newer seadoo 4 tec valves from 2007+? Would they be okay to spin up 8600Rpms if stock sprigs are used with titanium retainers?
  15. FS - Parts Hi, Can you pm me about the Air intake manifold?...

    Hi, Can you pm me about the Air intake manifold? Thank you
  16. Replies
    4
    Views
    191

    SOLD Now those can't be good... Unless they are...

    Now those can't be good... Unless they are ARPs....
  17. Replies
    4
    Views
    191

    SOLD ARP Head studs

    Does anyone have a good clean set of ARP head studs kicking around for the seadoo 4 tec engines?
  18. Replies
    12
    Views
    412

    Yes the cylinder head can be removed without...

    Yes the cylinder head can be removed without pulling the engine.. It probably caused damage to the piston as well..
  19. Replies
    7
    Views
    337

    I did return a full set of Connection rod bolts...

    I did return a full set of Connection rod bolts back to SBT in the past.. 2 of the 6 bolts were cross threaded, they wouldn't screw in by hand.
  20. Replies
    7
    Views
    337

    I installed a complete set of WSM bearings for...

    I installed a complete set of WSM bearings for $104 Usd... (Main bearings, counter balance bearings, connecting rod bearings and all half ring thrust bearings) Clearance were all good as well with...
  21. Replies
    23
    Views
    648

    I would try finding a newer block. It looks like...

    I would try finding a newer block. It looks like the thrust washer ate far to deep into the block. It will give you issues with the main bearing clearances..
  22. Non supercharger Stator/timing housing for supercharged applications.

    Curious to know if anyone has machined out the block/cap on non supercharged Stator/timing covers so it can be used for supercharged applications?
  23. Replies
    13
    Views
    392

    I was recommended to use 60s or 80s for a...

    I was recommended to use 60s or 80s for a ET137+4mm for a riva tune and Siemens ECU.. Wondering if the 50s would cause less starting issues (Flooding engine) when trying to start the engine hot??
  24. Replies
    23
    Views
    648

    Not checking clearances is 99% of the time why...

    Not checking clearances is 99% of the time why rebuild engines fail.. Especially with the high reving 4 tecs.
  25. Replies
    23
    Views
    648

    Are you referring to installing the half rings?

    Are you referring to installing the half rings?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4