Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds; generated 2 minute(s) ago.

  1. Replies
    2
    Views
    56

    Its worth paying for, it really is good software....

    Its worth paying for, it really is good software. There is also the option of setting up calculated fields if you want to go down a rabbit hole with advanced tuning.

    Sean
  2. Make a note of the hours and inform whoever you...

    Make a note of the hours and inform whoever you sell to. Its not a big deal.

    Sean
  3. Replies
    3
    Views
    52

    I think rhass makes "ufo" mounts which are like...

    I think rhass makes "ufo" mounts which are like little flanged nutserts made to be glassed in for motor mounts and the like. Check into them and see if they fit the bill.

    Sean
  4. Replies
    5
    Views
    97

    Trick setup, what driveshaft were you using when...

    Trick setup, what driveshaft were you using when it let loose?

    Sean
  5. Replies
    21
    Views
    353

    No kidding about the price, looks to be well made...

    No kidding about the price, looks to be well made stuff though.

    Sean
  6. Replies
    21
    Views
    353

    That is really interesting, I had not seen that...

    That is really interesting, I had not seen that setup. Thanks for sharing it. I have some more thinking to do now if the system works.

    Sean
  7. Replies
    21
    Views
    353

    Other than the mounts being different and the...

    Other than the mounts being different and the shoe being small on the 15f the pump should fit in the area without too much fitting.

    I have considered using the yamaha setup as well because the...
  8. Replies
    21
    Views
    353

    That threads into the yamaha midshaft coupler...

    That threads into the yamaha midshaft coupler though right?

    Without running an additional support on the end, I would be worried about the excess mass of the coupler on the end with the...
  9. Replies
    21
    Views
    353

    Do you know offhand which models they are? ...

    Do you know offhand which models they are?

    Kawasaki uses a stub shaft on the stator side that goes from the crank to the pto coupler so its not groundbreaking.

    Sean
  10. Replies
    21
    Views
    353

    I am not sure yet if I will even need to move the...

    I am not sure yet if I will even need to move the cooler but hopefully I can avoid cutting the hull or moving it.

    Regarding the coupler and shaft, another member mentioned that the yamaha vx110...
  11. Replies
    21
    Views
    353

    I don't plan on using the pto splines at all....

    I don't plan on using the pto splines at all. There is enough slop in them that if they weren't supported by the carrier and the the pump the end would flail around. The kawasaki coupler would make...
  12. Replies
    21
    Views
    353

    Interesting, thanks so much for posting. ...

    Interesting, thanks so much for posting.

    Given that the crank does feed oil to the pto I am not sure I want to block it off completely but I also don't want to run it unrestricted in case it...
  13. Replies
    6
    Views
    139

    It was a link to a site that collated a bunch of...

    It was a link to a site that collated a bunch of ads for baitcaster reels. I removed the link.

    Sean
  14. Replies
    6
    Views
    139

    Nice catch, I didn't look at the link. Sean

    Nice catch, I didn't look at the link.

    Sean
  15. Thanks, I will take you up on that offer at some...

    Thanks, I will take you up on that offer at some point. I have a few ideas in mind.

    Sean
  16. Replies
    6
    Views
    139

    Personally I prefer baitcasters but you have to...

    Personally I prefer baitcasters but you have to know how to cast them or they are a pain in the ass.

    If you mess up your cast with a spinning reel you can typically just reel it back in, on a...
  17. Replies
    21
    Views
    353

    Just a few pictures for reference. ...

    Just a few pictures for reference.

    453925453926453927453928

    Sean
  18. Replies
    12
    Views
    517

    You havn't noticed much power fluctuation from...

    You havn't noticed much power fluctuation from season to season, pump e85 varies in actual ethanol content month to month in most places.

    Sean
  19. Replies
    21
    Views
    353

    Spent some time this morning thinking through the...

    Spent some time this morning thinking through the coupler adapter and I am hoping to pick the brains of a few of y'all who are more experienced with the doo pto setup. I made a quick drawing of the...
  20. Replies
    12
    Views
    517

    Are you using a flex fuel sensor or just running...

    Are you using a flex fuel sensor or just running a fixed map?

    Sean
  21. The screws are also probably jis not phillips...

    The screws are also probably jis not phillips head. They look identical but are different.

    Sean
  22. Replies
    10
    Views
    256

    Typically I try to avoid "permanent" block mods...

    Typically I try to avoid "permanent" block mods but that is basically what I was thinging about doing.

    Yep, insead of water to coolant its water to oil.

    Sean
  23. Replies
    21
    Views
    353

    Doo powered STX-R and STX-15f Builds

    Starting this as a premptive strike and planning thread. I snagged this pair of neglected and nasty salt water skis (2008 rxtx and gtx) about a year ago and am finally getting around to doing...
  24. On the kawasaki skis, if the gauge is faulty but...

    On the kawasaki skis, if the gauge is faulty but connected they will still run. They run in slo mode but the engine runs. With the gauge disconnected they do not have power to the ecu at all.
    ...
  25. Replies
    1
    Views
    91

    WTB - Parts I should have one. Let me see if I can find it. ...

    I should have one. Let me see if I can find it.

    Sean
Results 1 to 25 of 187
Page 1 of 8 1 2 3 4