Search

Type: Posts; User: Doug78

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds; generated 24 minute(s) ago.

  1. Replies
    8
    Views
    588

    Sleeves can be bored, no nikasil. Mine is .020...

    Sleeves can be bored, no nikasil. Mine is .020 over and been fine. Unless something changed with the SVho blocks...but I don't think so.

    Aftermarket buckets are thicker and may require Grinding...
  2. Disregard my comments, totally thought you said...

    Disregard my comments, totally thought you said clutch only span one way.

    You need a clutch...simple.
  3. Replies
    23
    Views
    1,488

    They need.to go.back in where they came from. The...

    They need.to go.back in where they came from. The shims set the valve lash. If you swap everything around then the lash should be checked adjusted.
  4. Hey look a water cooled front sc housing, Guess...

    Hey look a water cooled front sc housing, Guess they are worth using.

    What wheel gets 40 lbs of boost?
  5. Replies
    11
    Views
    424

    What impeller did you have before?? Is it hopping...

    What impeller did you have before?? Is it hopping while get on plane at top speed??
  6. Replies
    8
    Views
    356

    Check injector harnesses, number 4 IIRC is a...

    Check injector harnesses, number 4 IIRC is a problem on the newer engines. Broken pin or wire in the connector.
  7. We know that after 70mph the 2019s have...

    We know that after 70mph the 2019s have unfavourable handling that the Riva plate fixes. It's possible the weight is making this problem come out at lower speed. Did you try trim adjustments? Did it...
  8. Replies
    20
    Views
    974

    Ha! Thanks to Uncle then, my bad. I've always...

    Ha! Thanks to Uncle then, my bad. I've always known ram hsd good stuff, just never bought any until now.
  9. Replies
    20
    Views
    974

    My ram mount arrived today, picking up my logging...

    My ram mount arrived today, picking up my logging kit and case tommorow
    Will try and share picture of my Fzr set up. All inspired by outlaws set up.
  10. I ran and abused a pc625 for 7 years and was...

    I ran and abused a pc625 for 7 years and was terrible at keeping a tender on it. Great battery.
  11. Replies
    1
    Views
    116

    SOLD Last call....thinking of heading another...

    Last call....thinking of heading another direction.
  12. Replies
    6
    Views
    243

    Guess I'm pulling pitch or adding boost. Easy...

    Guess I'm pulling pitch or adding boost. Easy stuff!
  13. Replies
    1
    Views
    116

    SOLD WTB engine tech 18psi wheel

    Would be shipped to northern Washington or Canada depending on what works best.

    Anyone got one?
  14. Replies
    6
    Views
    243

    I get that I will need to get drop pitch or add...

    I get that I will need to get drop pitch or add boost or both. I just expected that when the ski unhooked it would log a higher peak RPM than before.
  15. Replies
    6
    Views
    243

    Charger front housing, Maptuner questions.

    Could a old SHO front housing be machined to fit a SVHO wheel?? I think I have my old one from a shaft failure kicking around...

    Just loaded my maptuner stage 3 tune and confused about max rpm....
  16. Replies
    23
    Views
    1,442

    Engines are sleeved, the sleeves are cast into...

    Engines are sleeved, the sleeves are cast into the block on pretty well invisible. You can find them with a magnet.
  17. Replies
    3
    Views
    244

    I need shorter bolts mount mine without the...

    I need shorter bolts mount mine without the spacers. Picking up new bolts today, will post a picture of mine mounted later tonight or tomorrow. Probably going to run with spacers most of the year,...
  18. Replies
    3
    Views
    449

    WTB There is a couple here in canada, vanouver area....

    There is a couple here in canada, vanouver area.

    https://vancouver.craigslist.org/van/boa/d/richmond-2011-yamaha-fx-sho-18l/6848432524.html

    Or this one has been listed for around 6 months,...
  19. Replies
    56
    Views
    3,091

    Ah I see. I had an idea that might have been the...

    Ah I see. I had an idea that might have been the case. I started digging around annd noticed you where selling turbos at on point.
  20. Replies
    56
    Views
    3,091

    What wheel got you to 90 at 9200rpm on your FZR?

    What wheel got you to 90 at 9200rpm on your FZR?
  21. Replies
    56
    Views
    4,374

    They make a 4000 that is medium strength for...

    They make a 4000 that is medium strength for disassembley. That what I plan on using. If I can find it.
  22. Replies
    4
    Views
    275

    Jerry sells a super harger block off plate in the...

    Jerry sells a super harger block off plate in the store. Covers the oil gallery and charger opening.




    https://www.4-tecperformance.com/images/R&D%20supercharger%20block%20off.png
    OEM Yamaha...
  23. Feels like I could get good cash for my...

    Feels like I could get good cash for my water-cooled front housing.
  24. Replies
    18
    Views
    1,000

    That dry suit looks pretty good! I like the two...

    That dry suit looks pretty good! I like the two way function. My question is how well does it breathe?? I spent two weeks in a kokatat goretex dry suit riding up to 8 hours in shit seas and loved it....
  25. Thread: GP1800 parts

    by Doug78
    Replies
    16
    Views
    756

    FS - Parts Curious why you chose not to run the buckets with...

    Curious why you chose not to run the buckets with the dual valve springs?? I have a PO box in Blaine, pondering the pump...98230
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4