Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Welcome to GreenHulk. Blowing into the tank and...

    Welcome to GreenHulk.
    Blowing into the tank and hearing bubbles is the fuel supply hose. Being able to turn it off with the fuel switch confirms it.
    The supply hose will split into 2 hoses and feed...
  2. Replies
    4
    Views
    72

    The CDI's that only have the PVL number are gen1...

    The CDI's that only have the PVL number are gen1 -non updated CDI'S.

    The 4010803 CDI is a Gen3 cdi. You will need to replace the stator with either a "update" stator which will be a direct...
  3. Replies
    2
    Views
    49

    I think you are talking about the plastic nut...

    I think you are talking about the plastic nut that holds the cable at the hull pass thru.
    Lugs found something that works at HomeDepo to replace that plastic nut.
  4. Replies
    1
    Views
    63

    Welcome to Greenhulk ! If you had to buy a new...

    Welcome to Greenhulk !

    If you had to buy a new CDI from the dealer-your only option would be an update kit (Gen3 CDI/stator/coil).

    A used CDI will work just fine on a 22 year old craft.
    Post a...
  5. Replies
    2
    Views
    63

    Not very rough, that black sticker on the front...

    Not very rough, that black sticker on the front fades in like 30 hours of use. After 22 years, I would think it needs some work , worst part is the previous mechanic.
  6. Replies
    1
    Views
    41

    It has a mechanical fuel pump on the side of the...

    It has a mechanical fuel pump on the side of the carb. one of the 3 hoses is the 'pulse' line that attaches to the crank case.

    The pulse is caused by the piston going up and down, so will be...
  7. Replies
    3
    Views
    129

    FS - Parts Replied. Thankyou.

    Replied. Thankyou.
  8. Replies
    3
    Views
    129

    FS - Parts Selling New MSX cover red/grey 2859039

    I am selling 1 new in the box MSX cover made by Polaris.
    Part # 2859039, it is the grey with red version.
    I personally opened the box to inspect the material and cover condition which are great, I...
  9. Replies
    1
    Views
    75

    Timing.

    Timing.
  10. Replies
    1
    Views
    62

    Timing

    Timing
  11. Replies
    4
    Views
    137

    There should be a way to grease the bearing, look...

    There should be a way to grease the bearing, look for a grease fitting or plug where a grease fitting can be threaded into.

    Worse case-chances are the drive shaft will need to be replaced-cut the...
  12. Replies
    4
    Views
    137

    The part you have circled is the thru hull seal,...

    The part you have circled is the thru hull seal, although it is the aftermarket design. It should just slide on the driveshaft, that design does use an actaual roller bearing-that bearing may have...
  13. Replies
    17
    Views
    450

    Polaris jet pumps do make noise at the...

    Polaris jet pumps do make noise at the impeller/drive shaft joint. Make sure the splines are pretty square. No play-roughness-binding in pump bearings.
    Retest.
  14. Replies
    11
    Views
    221

    97 was the last year for the Fuji engine ,other...

    97 was the last year for the Fuji engine ,other then the PRO785. But Polaris made a SL1050 in 97. The 1050 is exactly the same size on the outside. Side by side you can not tell the difference.
    I...
  15. Replies
    17
    Views
    450

    Yep, should see the scale at TDC. Does the...

    Yep, should see the scale at TDC. Does the flywheel have a scale ? I have seen the corrode so bad,they are not visible.

    Otherwise the flywheel must have moved, we have seen the crank "key" break,...
  16. Replies
    3
    Views
    105

    Will it rev up on the trailer ?

    Will it rev up on the trailer ?
  17. Thread: No RPM on MFI

    by casey67
    Replies
    5
    Views
    110

    Check your "notifications" at the top of page.

    Check your "notifications" at the top of page.
  18. Replies
    3
    Views
    81

    Correct on jet pump and shaft inorder to get the...

    Correct on jet pump and shaft inorder to get the seal out. Probably will need to get the seal moving on the shaft to get the shaft out.
  19. Thread: No RPM on MFI

    by casey67
    Replies
    5
    Views
    110

    Was it NEW, or a different MFI ? Did it also go...

    Was it NEW, or a different MFI ? Did it also go into 'limp mode"/misfire ?
    The older MFD's did cause misfire on rare occasions. Does the MFI have water/moisture in it ?

    The LR is the voltage...
  20. Replies
    3
    Views
    81

    Yes, that is the "thru hull" seal assembly. Also...

    Yes, that is the "thru hull" seal assembly. Also refered to as the drive shaft bearing.

    Looks like you have the aftermarket style-that actually has roller bearings inside.
    The stock one has more...
  21. Replies
    17
    Views
    450

    If there is fuel at the diaphragm, there is...

    If there is fuel at the diaphragm, there is nothing to stop the fuel from flowing. The jets-when not clogged, restrict fuel to a dribble.

    Placing your hand over the carb while cranking, your hand...
  22. Thread: No RPM on MFI

    by casey67
    Replies
    5
    Views
    110

    If it is in "limp Mode" It will have a warning on...

    If it is in "limp Mode" It will have a warning on the display-such as Over heat. Also a flashing red light at the top of MFI.

    If the problem goes away when taking out the MFI-then the problem is...
  23. Replies
    17
    Views
    450

    Welcome to GreenHulk Were the hoses marked...

    Welcome to GreenHulk

    Were the hoses marked before removing ?
    The upper most hose is the return. Lowest is the supply-blowing into supply hose should make bubbles in the fuel tank.

    The needle...
  24. Replies
    4
    Views
    154

    You can look up parts and search which models...

    You can look up parts and search which models will use that exact number here; http://parts.polarisind.com/Browse/Browse.asp

    All the MFD's use the same basic design and can be interchanged-might...
  25. Replies
    6
    Views
    122

    If you unplug the MFI, the engine will not...

    If you unplug the MFI, the engine will not crank.Jump pin 1 (Purple/White) and 3 (Black) and it should crank.
    Unplugging the MFI will not affect anything else.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4