Search

Type: Posts; User: raven007

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Stan Lee

    by raven007
    Replies
    23
    Views
    1,770

    I stopped at chocolate cream pie. :facepalm::)

    I stopped at chocolate cream pie. :facepalm::)
  2. Thread: 2020 Lineup ?

    by raven007
    Replies
    53
    Views
    3,045

    in direct contrast to my "that thing still...

    in direct contrast to my "that thing still runs...." experiences.
  3. Replies
    9,040
    Views
    470,759

    welp... i know what any new 9mm carbine builds...

    welp... i know what any new 9mm carbine builds will be using for magazines....
  4. Remove air filter. Good spark plugs. Make sure...

    Remove air filter. Good spark plugs. Make sure the pump is tight with a good wear ring and impeller. That's basically all you can do for a vx110. You can not put fxho throttle bodies on and run the...
  5. Replies
    20
    Views
    5,115

    I hate to bring up an old thread, but this is...

    I hate to bring up an old thread, but this is literally the only resource I have found on doing this.

    If you were not doing a turbo build, would there be enough room for the exhaust without the...
  6. Unless someone has glued it on, it shouldnt take...

    Unless someone has glued it on, it shouldnt take a lot to get it moving.
  7. Replies
    9,040
    Views
    470,759

    Was a torched parts kit. I built a multipart...

    Was a torched parts kit. I built a multipart aluminum jig to hold the stubs, and the repair section to final length. Tigged it up (I am still learning TIG so don't rip me for not stacking dem dimes)....
  8. Replies
    9,040
    Views
    470,759

    any builders here? (yes its semi and fully...

    any builders here? (yes its semi and fully compliant)

    http://greenhulk.net/forums/attachment.php?attachmentid=454185&stc=1
  9. Replies
    75
    Views
    2,238

    I still think the best plan is making the engine...

    I still think the best plan is making the engine "look" like a kawasaki from a coupler perspective, Either through a stub shaft or something. I honestly don't think whipping will be an issue with a...
  10. Replies
    12
    Views
    434

    I would start suspecting something like the key...

    I would start suspecting something like the key is sheared in the flywheel.
  11. yup. ...

    yup.
    http://greenhulk.net/forums/attachment.php?attachmentid=454134&stc=1
  12. Replies
    6
    Views
    507

    A 250x is equally worthless either way. LOL ...

    A 250x is equally worthless either way. LOL

    Disclaimer: I own one, so I can rip on them.
  13. LX is a 15f motor. 250x is a, wait for it, 250x...

    LX is a 15f motor. 250x is a, wait for it, 250x motor.
  14. Replies
    75
    Views
    2,238

    Why dont you let the seadoo driveshaft extend...

    Why dont you let the seadoo driveshaft extend through the kawasaki coupler. Like bore it through and turn it down so its like a the pilot bearing part of a manual tran sinput shaft. this goes through...
  15. Replies
    75
    Views
    2,238

    The splines fit the early VX110 pump, the one...

    The splines fit the early VX110 pump, the one that is built like a kawasaki and seadoo without the driveshaft attached. Source: Me! I used the spline tool to swap an impeller and it fit nice and...
  16. Replies
    11
    Views
    532

    I personally always wanted to put a valve on it...

    I personally always wanted to put a valve on it and a nozzle on the handlebars so i could use it as a giant squirt gun.
  17. Replies
    12
    Views
    504

    My evidence is anecdotal at best. But locally I...

    My evidence is anecdotal at best. But locally I have seen three blown up TR1s running alongside MR1s with 3 times as many hours. Same maintenance, same riding conditions. One with bottom end...
  18. Replies
    11
    Views
    532

    Its direct from the pump output. So water goes in...

    Its direct from the pump output. So water goes in the pump and out the nozzle. Gay spray is tapped from the reduction nozzle area.
  19. Replies
    12
    Views
    504

    A TR1 aint gonna make it 800 hours. The old 110...

    A TR1 aint gonna make it 800 hours. The old 110 horse MR1 would do it with maintenance.
  20. Replies
    4
    Views
    190

    You have to pull the exhaust to get the engine...

    You have to pull the exhaust to get the engine out in my experience. That one bolt is a pain. I think I use a 12 point box end wrench on it if its the one I am thinking of.
  21. Replies
    2
    Views
    242

    unlike old school skis where it grounds the cdi,...

    unlike old school skis where it grounds the cdi, most modern skis have a shutdown pin on the ecm. When the lanyard is pulled it tells the ecm to kill the engine, a little while later it drops the...
  22. Replies
    1
    Views
    173

    WTB - Parts Bad stx-12f/15f ECM

    Looking for a dead ecm for stx-12f/15f. My plan is to de-pot all the epoxy off the board and reuse the connector for my standalone.
  23. i just threw up in my mouth a little. And it...

    i just threw up in my mouth a little. And it wasn't last nights whiskey.
  24. I have an early (like first year IIRC) 12f (the...

    I have an early (like first year IIRC) 12f (the "sow's ear" project boat I post about) that the entire manifold was just....gone. It was corroded so badly that the holes were plugged. And I got a 15f...
  25. Replies
    7
    Views
    359

    Keep that filter fresh! You don't want it to rust...

    Keep that filter fresh! You don't want it to rust and start leaking.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4