Search

Type: Posts; User: psycho rxp

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    40
    Views
    6,266

    FS You don’t happen to have a CMD or power commander...

    You don’t happen to have a CMD or power commander unit hooked up that 07’ do you? I had the power commander go bad and had the same #3 injector go full blast. I put in the bypass clip, and it would...
  2. Replies
    3
    Views
    103

    What rpm are you spinning? You should run open...

    What rpm are you spinning? You should run open loop cooling above 8800 RPMs
  3. Replies
    12
    Views
    312

    Yeah, I would say you got jipped on that item #-o

    Yeah, I would say you got jipped on that item #-o
  4. Replies
    33
    Views
    635

    @ what Rev limit?

    @ what Rev limit?
  5. Replies
    4
    Views
    117

    When you change the weight of the rotating...

    When you change the weight of the rotating assembly you should get it re-balanced.
    I’ve heard of a few using the Molnar rods, but the rod bolts were smaller 5/16”, vs the OEM 3/8” bolts.
  6. Replies
    6
    Views
    195

    FS I would call Riva to verify it, that’s how they...

    I would call Riva to verify it, that’s how they have been in the past.
  7. Replies
    6
    Views
    195

    FS If it was used on that ski, it is Vin locked to...

    If it was used on that ski, it is Vin locked to that ski only , and is now a paperweight.
  8. 80% is perfect

    80% is perfect
  9. On the 19 TX, you don’t have to pull the IBR...

    On the 19 TX, you don’t have to pull the IBR fuses to flash it.

    When I first flashed it, it only ran 8000 RPMs at 75 mph (stock prop), so
    I D-pitched my stock prop about 2.5 mm, and now turn...
  10. View Post

    That’s exactly what I did , but ran it On top of the stock air box. Just had to re-locate the fuse panel, to run the Kana flex through that area. Cost about $100.
  11. Replies
    37
    Views
    796

    U would need this kit...

    U would need this kit
    https://www.4-tecperformance.com/index.php?main_page=product_info&cPath=18_63&products_id=763

    & all the special tools to do the supercharger, found here
    ...
  12. Replies
    49
    Views
    3,631

    The driveshaft groove and C-clip can wear out...

    The driveshaft groove and C-clip can wear out overtime, which also causes a wobble in your carbon seal. On my first ski the dealer warrantied my driveshaft , from a worn out groove. Have them checked...
  13. Replies
    37
    Views
    796

    All 08+ skis came with metal washers. No ceramics

    All 08+ skis came with metal washers. No ceramics
  14. Replies
    1
    Views
    102

    You might want to try to free air calibrate the...

    You might want to try to free air calibrate the 02 sensor, or replace it with a brand new one. If you’re getting 10.0 AFR, then you have way too much fuel, injector wise or pressure wise. You need to...
  15. Replies
    50
    Views
    3,112

    Show a picture of your fuel pressure screen as...

    Show a picture of your fuel pressure screen as well, with your Below 2000 RPM cells
  16. Replies
    50
    Views
    3,112

    Looks ok, but bring up your target afr to the...

    Looks ok, but bring up your target afr to the 2250 rpm line

    450747
  17. Replies
    12
    Views
    312

    They put the new gauges in the 18s later in the...

    They put the new gauges in the 18s later in the year. The buttons are different on the Newer style gauges.
    If you have the older style gauges the cruise button is on the right handlebar at the top....
  18. You should start a thread in the Yamaha section...

    You should start a thread in the Yamaha section of the forum for that question.
  19. Replies
    12
    Views
    312

    If you have the new style gauges, the left...

    If you have the new style gauges, the left control pad right button, looks like a little speedometer gauge button. Push that while at any speed to engage cruise control
  20. Replies
    50
    Views
    3,112

    That chart looks pretty good, but my motor ran a...

    That chart looks pretty good, but my motor ran a little better, closer to 13.2 at idle.
  21. Replies
    6
    Views
    175

    No, you usually set the rising rate regulator for...

    No, you usually set the rising rate regulator for the proper AFR @ wide-open throttle only. The rest is in the tune & injectors it was mapped for. The only way to dial-in the idle and mid range is...
  22. Replies
    4
    Views
    104

    https://www.ebay.com/itm/Sea-Doo-New-OEM-Instrumen...

    https://www.ebay.com/itm/Sea-Doo-New-OEM-Instrument-Gauge-Speedometer-Cluster-278002270-GTX-RXP-RXT-Wake/202137897917?epid=12013149464&hash=item2f105b8bbd:g:OUkAAOSwdhdcGZTr

    Or RETAIL
    450694
  23. Replies
    4
    Views
    104

    If all the connections to your battery & gauges...

    If all the connections to your battery & gauges are tight, then you need a new Dash. The early 06-07 gauges were black faced and faded or stopped working after time. The newer replacement ones have...
  24. Replies
    6
    Views
    226

    If you put the bucket in IBR override position,...

    If you put the bucket in IBR override position, to raise it up for maintenance, then try to start it in reverse, you’ll get the error. , Just shutting off and re-keying, will make it go away. I had...
  25. Replies
    40
    Views
    2,579

    The T-X’s do, not sure on the P-X’s

    The T-X’s do, not sure on the P-X’s
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4